Casper is now there!!!!
#65
TECH Junkie
Thread Starter
iTrader: (3)
Join Date: May 2003
Location: Clayton, North Carolina
Posts: 3,898
Likes: 0
Received 6 Likes
on
6 Posts
Kevin is working on the video's now. The 7.04 run video is the best to watch because Mike only pulled one chute and ended up in the sand. He takes the car into the sand sideways so nothing goes into the turbo's! The 6.86 video is good also, you can see him correct after the wheels touchdown. Then the windshield bends in!
Tom- I still have my welded up AFR's on the engine.
Kurt
Tom- I still have my welded up AFR's on the engine.
Kurt
#68
TECH Resident
iTrader: (1)
Join Date: Dec 2001
Location: TX
Posts: 753
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 777
I'm pretty sure that motor will not fit into your normal f-body
Its an iron block correct? then why wouldnt it fit? they would have to redo the plumbing, but i dont see why it would'nt fit.
Its a very impresive car, i know they built it to test the lsx motor out at the track.
what tire? raceweight?
Last edited by TApimp; 08-16-2005 at 10:18 AM.
#72
LS1TECH Sponsor
Join Date: Nov 2004
Location: Michigan
Posts: 344
Likes: 0
Received 0 Likes
on
0 Posts
In car 6.86 video. Note the windshield buckle in high gear.
http://www.w2wpowertrain.com/images_...r_6.86_run.wmv
http://www.w2wpowertrain.com/images_...r_6.86_run.wmv
Last edited by Kev@WheeltoWheel; 08-16-2005 at 11:31 AM.
#73
TECH Senior Member
iTrader: (15)
Join Date: Nov 2001
Location: Grand Prairie, TX
Posts: 5,109
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Kev@WheeltoWheel
In car 6.86 video. Not the windshield buckle in high gear.
http://www.w2wpowertrain.com/images_...r_6.86_run.wmv
http://www.w2wpowertrain.com/images_...r_6.86_run.wmv
#75
TECH Senior Member
iTrader: (15)
Join Date: Nov 2001
Location: Grand Prairie, TX
Posts: 5,109
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 777
It's a work in progress. I'd say it's got more in it, but it's not the first run.
#76
SSU'S Vice Mod
Join Date: Jul 2004
Location: Hazard Co. Maryland
Posts: 2,391
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 427
Not sure what the 352 will do next, but some engine dyno time is in order. According to the info collected, we are over 1900hp at the flywheel!!!
Kurt
Kurt
Dang Kurt, that is impresive right there! Considering those Lencos soak up a fair amount of power, and I'm guessing that you're somewhere around 3000 lbs with Moran in the car, you're looking at about 1425 to the wheels? Unbelievable, congrats again.
#77
SSU'S Vice Mod
Join Date: Jul 2004
Location: Hazard Co. Maryland
Posts: 2,391
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Sandmann120
So, who will be the first to put a Gen III on blown nitro?
you are nuts. Probably have to wait for aftermarket 5 head bolt block and heads to try that though
#78
LS1TECH Sponsor
Join Date: Nov 2004
Location: Michigan
Posts: 344
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by V6 Bird
I was only basing that on the wiring from the cockpit side.
It's common practice to run wiring across the dash bar in a tube chassis vehicle and was existing prior to our work on it.