Stock Long block LS2 breaks 700whp!!!!!
#1
Thread Starter
LS1Tech Sponsor
iTrader: (10)
Joined: Mar 2004
Posts: 4,439
Likes: 3
From: Spring Lake, MI
Stock Long block LS2 breaks 700whp!!!!!
Well we dyno'd the 05 GTO. Stock long block right to the valve springs. S374 Bullseye turbo @15psi. This was a really conservative dyno too.
735rwhp@5400
745rwtq@4900
This was with 110, and meth injection.
pics and videos tonight.
735rwhp@5400
745rwtq@4900
This was with 110, and meth injection.
pics and videos tonight.
#4
Very nice, Duttweiler barely made that on an engine flywheel type dyno with a well built 402 at around the same compression and boost. You're kicking some *** there, congrats TJ.
#6
thats awesome.I love it.i made about 630 rwhp with a maggie at 10lbs and a 50 shot.I really like people who push the stock blocks and take a dare.its all in the tune.
Trending Topics
#13
Thread Starter
LS1Tech Sponsor
iTrader: (10)
Joined: Mar 2004
Posts: 4,439
Likes: 3
From: Spring Lake, MI
Just a couple pics, I will get more, or have dave post them up. On the 565rwhp baseline tune it went 11.7@131, with a 3950#lb race weight. Should go 140 now.
The passenger side manifold is stock with a cross over under the bell housing. driver side manifold is a 6l truck manifold. Waste gate is a JGS 40mm unit From FI. It has 60's, rails, a-1000 and the stock tank is sumped with a return. Clutch is a Ram dual disk. The S374 has the race cover with a t4 1.1 hot side. Comes on super quick and has fairly low IATs at this boost level.
The passenger side manifold is stock with a cross over under the bell housing. driver side manifold is a 6l truck manifold. Waste gate is a JGS 40mm unit From FI. It has 60's, rails, a-1000 and the stock tank is sumped with a return. Clutch is a Ram dual disk. The S374 has the race cover with a t4 1.1 hot side. Comes on super quick and has fairly low IATs at this boost level.
#16
Can we take bets on how long it will last lol.
I wonder if you just changed to forged pistons and arp rod bolts how long it would last and how much you could push it, oh yea and some good valvesprings too. I would bet close to 800 and actually lasting a while.
I wonder if you just changed to forged pistons and arp rod bolts how long it would last and how much you could push it, oh yea and some good valvesprings too. I would bet close to 800 and actually lasting a while.
#18
#19
Awsome numbers, this is going to inspire me. Pardon the ignorance but the wavyness of the low boost power curve, is that from compressor surge or other random issues? Any chance of a 4" downpipe behind that monster?
#20
Thread Starter
LS1Tech Sponsor
iTrader: (10)
Joined: Mar 2004
Posts: 4,439
Likes: 3
From: Spring Lake, MI
That has a lot to do with bringing lots of meth in and a AFR that moved around because of that. Also I tried to keep the torque down to save the bottom end. So in the bottom the ignition advance is still in the single digits. There was a lot of room to make more power every where but I decided it would be better to try my best at keeping the bottom end together. With the fuel we were running, 18 degress across the board in boost would have not been a problem. If it had good parts in it that would have been a 900+ graph lol.
Last edited by hellbents10; 11-21-2007 at 11:09 AM.