best header/y combo >700

Reply Subscribe

Thread Tools

Search this Thread

Feb 17, 2004 | 03:06 PM

12stones

Thread Starter

TECH Resident

iTrader: (2)

Joined: Jan 2004

Posts: 896

Likes: 0

From: Cornelius, NC

best header/y combo >700

i think i'm pretty set on getting pacesetter coated lt's and a catted pacesetter y-pipe and having a muffler shop weld on a flowmaster collector. i dont wanna spend more then 700. any other suggestions on the best headers and/or y-pipe and say under my target price. thanks for all

Feb 17, 2004 | 05:33 PM

davered00ss

Moderator

iTrader: (4)

Joined: Nov 2003

Posts: 10,520

Likes: 0

From: Plainfield, CT

I don't think Pacesetter makes a Catted-Y. You would have to have someone fab one up for you.

Feb 17, 2004 | 10:52 PM

12stones

Thread Starter

TECH Resident

iTrader: (2)

Joined: Jan 2004

Posts: 896

Likes: 0

From: Cornelius, NC

i beilve they do, at ls1speed.com although as always i'm up for correction

Feb 17, 2004 | 11:02 PM

foff667

LS1TECH Sponsor

iTrader: (2)

Joined: Jul 2003

Posts: 7,986

Likes: 3

From: Clermont, FL

your up for correction then...i even went so far as to check their site no catted ypipe on there to be found. and youd be hardpressed to be able to put cats into their design.

lata
Bill

Feb 17, 2004 | 11:26 PM

12stones

Thread Starter

TECH Resident

iTrader: (2)

Joined: Jan 2004

Posts: 896

Likes: 0

From: Cornelius, NC

oops, well corrected i supose but i was referring to a catted pipe as being one w/o cats. my mistake. but at any rate for less then $700, does pacesetter lt's, offroad y, and flowmaster collecter seem to be my best bet? thanks for all

Feb 17, 2004 | 11:27 PM

foff667

LS1TECH Sponsor

iTrader: (2)

Joined: Jul 2003

Posts: 7,986

Likes: 3

From: Clermont, FL

for less than $700 probably

Feb 17, 2004 | 11:27 PM

12stones

Thread Starter

TECH Resident

iTrader: (2)

Joined: Jan 2004

Posts: 896

Likes: 0

From: Cornelius, NC

also, foff667, did your pacesetter y come crushed like that? if so is that for clearence? could i get around having mine like that somehow?

Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin

Verdad Gallardo

6 Common C5 Corvette Failures and What's Involved In Repairing Them

Pouria Savadkouei

Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph

Verdad Gallardo

Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked

Pouria Savadkouei

Top 10 Most Powerful Chevy Trucks Ever Made!

Hennessey's New Supercharged Silverado ZR2 Has 700 HP

Verdad Gallardo

Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes

Verdad Gallardo

Awesome K5 Blazer Restomod Comes With C7 Corvette Power

Verdad Gallardo

10 Camaros You Should Never Buy

10 LS Engine Myths That Refuse to Die

Verdad Gallardo

Feb 17, 2004 | 11:35 PM

12stones

Thread Starter

TECH Resident

iTrader: (2)

Joined: Jan 2004

Posts: 896

Likes: 0

From: Cornelius, NC

foff667, while you seem to be on here alot tonight, lemme ask you a question about your header/y install, i'll be doing this by my self and i'll have acess to lift at my highschool, what tips, helpful hints would you give me to acheve this install with as few headaches as possible. thanks

Feb 17, 2004 | 11:39 PM

#10

foff667

LS1TECH Sponsor

iTrader: (2)

Joined: Jul 2003

Posts: 7,986

Likes: 3

From: Clermont, FL

have someone with skinny *** arms to get to the rear most manifold bolts, and grind or cut the kmember before you tighten donw the headers, cut off the nub of the block using a sawsal it will take all of 30 seconds, will not affect appearance or anything so dont worry about it too much...and most important have fun