Generation III External Engine LS1 | LS6 | Bolt-Ons | Intakes | Exhaust | Ignition | Accessories
Sponsored by:
Sponsored by:

Losing power and dont know why!!!!!

Thread Tools
 
Search this Thread
 
Old Mar 17, 2012 | 11:02 AM
  #1  
drebear34's Avatar
Thread Starter
Teching In
 
Joined: Sep 2011
Posts: 13
Likes: 0
From: Georgia
Default Losing power and dont know why!!!!!

Ok, here's my problem.... My car was losing big time power especially when going up hills. When I stomp the accelerator, my RPM's shout up but it feels as though my car is stuck in gear. I just had both cats along with all 4 O2 sensors replaced. Any feedback would be greatly appreciated!!
Reply
Old Mar 17, 2012 | 11:49 AM
  #2  
nomasterase's Avatar
12 Second Club
iTrader: (4)
 
Joined: Jun 2011
Posts: 266
Likes: 0
Default

check your fuel pressure. have your changed out the fuel filter lately?
Reply
Old Mar 17, 2012 | 01:06 PM
  #3  
drebear34's Avatar
Thread Starter
Teching In
 
Joined: Sep 2011
Posts: 13
Likes: 0
From: Georgia
Default

Originally Posted by nomasterase
check your fuel pressure. have your changed out the fuel filter lately?
Yes sir, I actually had it replaced about 3 months ago. A friend of mine told me that it sounds as though my computer hasn't reset after the new cats, O2 sensors. Could there be so truth to that?
Reply
Old Mar 17, 2012 | 01:33 PM
  #4  
Dano02SS's Avatar
Teching In
 
Joined: Mar 2008
Posts: 23
Likes: 0
From: Memphis
Default

Same problem here. My camaro usually runs 10.50's on motor and is running 11.50's now. What could cause this? Changing fuel filter today. Put new valve springs in last fall and new plugs a few days ago. Any ideas?
Reply
Old Mar 17, 2012 | 01:36 PM
  #5  
omarrakeen's Avatar
TECH Addict
iTrader: (2)
 
Joined: May 2009
Posts: 2,472
Likes: 1
From: UAE, Dubai.
Default

why did you replace cats? were they clogged? car should relearn after few cycles..2 to 3 rides..when was the last time you changed spark plugs and wires? air filter? engine codes?
Reply
Old Mar 17, 2012 | 02:03 PM
  #6  
drebear34's Avatar
Thread Starter
Teching In
 
Joined: Sep 2011
Posts: 13
Likes: 0
From: Georgia
Default

Originally Posted by omarrakeen
why did you replace cats? were they clogged? car should relearn after few cycles..2 to 3 rides..when was the last time you changed spark plugs and wires? air filter? engine codes?
Well, I replaced my cats because of the rattling I heard one day when I started my car then the change in power lose. I had my Magnaflow cats put on yesterday, both sides, and my mechanic told me they were very clogged up and that my O2 needed to be replaced ASAP, so they got replaced. Now, to find out that the rattling that I heard wasnt my cat, it was my rear passenger coil springs vibrating causing the rattling noise. I had the plugs and wires changed about 4 months ago. Now air filter, hmmmm, that could be a possibility, and the only engine code was for my O2 sensor which I knew about......
Reply
Old Mar 17, 2012 | 02:54 PM
  #7  
omarrakeen's Avatar
TECH Addict
iTrader: (2)
 
Joined: May 2009
Posts: 2,472
Likes: 1
From: UAE, Dubai.
Default

Originally Posted by drebear34
Well, I replaced my cats because of the rattling I heard one day when I started my car then the change in power lose. I had my Magnaflow cats put on yesterday, both sides, and my mechanic told me they were very clogged up and that my O2 needed to be replaced ASAP, so they got replaced. Now, to find out that the rattling that I heard wasnt my cat, it was my rear passenger coil springs vibrating causing the rattling noise. I had the plugs and wires changed about 4 months ago. Now air filter, hmmmm, that could be a possibility, and the only engine code was for my O2 sensor which I knew about......
yep, clean or replace your filter and while you're there try to reset the car by unplugging the battery terminal for sometime..it might help.
Reply
Old Mar 17, 2012 | 03:27 PM
  #8  
nomasterase's Avatar
12 Second Club
iTrader: (4)
 
Joined: Jun 2011
Posts: 266
Likes: 0
Default

Also make sure your maf sensor is clean
Reply
Old Mar 17, 2012 | 06:17 PM
  #9  
drebear34's Avatar
Thread Starter
Teching In
 
Joined: Sep 2011
Posts: 13
Likes: 0
From: Georgia
Default

Originally Posted by nomasterase
Also make sure your maf sensor is clean
Thanks alot for your help. I will let you know the outcome.
Reply
Old Mar 17, 2012 | 09:50 PM
  #10  
drebear34's Avatar
Thread Starter
Teching In
 
Joined: Sep 2011
Posts: 13
Likes: 0
From: Georgia
Default

Originally Posted by nomasterase
Also make sure your maf sensor is clean
Whats a easy way to clean my MAF sensor?
Reply
Old Mar 17, 2012 | 10:04 PM
  #11  
L80Killa87's Avatar
Staging Lane
iTrader: (8)
 
Joined: Aug 2007
Posts: 73
Likes: 0
From: Lansing, KS
Default

Originally Posted by drebear34
Whats a easy way to clean my MAF sensor?
Spray the hell out of it with some maf cleaner and let it dry.
Reply




All times are GMT -5. The time now is 08:59 AM.