Anyone Powdercoated your LSx Engine Blocks?
#1
Staging Lane
Thread Starter
iTrader: (7)
Join Date: Sep 2006
Location: Richland, WA
Posts: 52
Likes: 0
Received 0 Likes
on
0 Posts
Anyone Powdercoated your LSx Engine Blocks?
Howdy Gents:
I have an '06 LS2 with only 600 miles on it that's on an engine stand. My question is this: Has anyone powder coated thier existing blocks?
I know thermal mass is an issue (getting the entire block up to temperature) and thus you probably have to disassemble it first but I'm concerned what will happen if the block is elevated to ~400°F (powdercoating forums say it may take several hours to get it to temperature). Given that the engine is near new and I'm not looking to build a radical engine, I would just assume reassemble the bottom end, perhaps with new bearings. I know the blocks from GMPP are coated but they have to be final machined. In a perfect world you would powdercoat first, then machine, then assemble new, but what can I say... I'm cheap and I don't see any reason to install new parts.
Any insight would be appreciated!
I have an '06 LS2 with only 600 miles on it that's on an engine stand. My question is this: Has anyone powder coated thier existing blocks?
I know thermal mass is an issue (getting the entire block up to temperature) and thus you probably have to disassemble it first but I'm concerned what will happen if the block is elevated to ~400°F (powdercoating forums say it may take several hours to get it to temperature). Given that the engine is near new and I'm not looking to build a radical engine, I would just assume reassemble the bottom end, perhaps with new bearings. I know the blocks from GMPP are coated but they have to be final machined. In a perfect world you would powdercoat first, then machine, then assemble new, but what can I say... I'm cheap and I don't see any reason to install new parts.
Any insight would be appreciated!
Last edited by kaptainkw; 12-21-2008 at 03:23 PM.
#2
Teching In
iTrader: (2)
Join Date: Sep 2008
Location: Temecula, CA
Posts: 20
Likes: 0
Received 0 Likes
on
0 Posts
I think you may have more problems than just the coating process. I am from very old school so things may have changed. I have always been of the opinion that you are not suppose to even paint an aluminum engine part. The aluminum parts are designed to dissipate heat in a way to maintain proper shape and trueness. Placing a coat of anything on the part is akin to putting a blanket on it. Heat is now an issue while in use.
#4
TECH Resident
iTrader: (17)
leave it alone, dont powdercoat any part of the block/heads/oil pan/tranny or almost any major component thats aluminum like stated. You can powdercoat brackets and things of that nature but not parts that get real hot and eventually need to cool down. how bout polishing your block and heads??? That'll be fun to maintain
#5
I own a powdercoating buisness and I have never done one for that reason. Im gonna go with, If you let the person who is going to coat it you car concirned with heat dissipation they can always just put a coat for color on and not layer it up thick. They will also mask off any of the large areas that you will not see such as the bellhouse area. Making the powder slightly thinner will also take away from the durability a little bit.
Trending Topics
#8
Motorboater
iTrader: (53)
ceramics are not for dissipation, they are for keeping the heat inside the substrate. ie--headers. ceramics are really not meant to be a topcoat, but rather an inside coat, that's how they work. for example if you coated a set of headers and didn't run it down the inside, eventually the outside ceramic would fail from all the heat pounding on it from inside the pipe. the ceramic coating on the inside of the tubes is what is really the functional portion, the outside is added protection and mostly for appearance.
as for the engine block, I haven't had any customer want to do one yet, no direct experience there.
as for the engine block, I haven't had any customer want to do one yet, no direct experience there.
#10
TECH Apprentice
Join Date: Nov 2006
Location: Copenhagen
Posts: 369
Likes: 0
Received 0 Likes
on
0 Posts
ive seen plenty of people painting and coating alloyblocks, you will eb fine.. just be sure to clean and scuff the entire block (dry ice blasting it prior to coating would propably do wonders for adheasion)
#12
TECH Apprentice
Join Date: Nov 2006
Location: Copenhagen
Posts: 369
Likes: 0
Received 0 Likes
on
0 Posts
the outside of the block wont get hotter than boiling water... ever! so any engine paint, quality automotive paint... BC/CC or SS will be just fine... just get the surface clean first!
#13
Staging Lane
Thread Starter
iTrader: (7)
Join Date: Sep 2006
Location: Richland, WA
Posts: 52
Likes: 0
Received 0 Likes
on
0 Posts
come on guys!!! ..... aluminum blocks arent designed to dissipate heat, thats what the cooling system is for... the surface hes wanting to powdercoat is on the OUTSIDE of the waterjacket... it will make NO difference in cooling since the LS engine isnt aircooled!, by your logic 5.3 or 6.0 L iron block should overheat with a coolingsystem from an ls1,2 or 3....
ive seen plenty of people painting and coating alloyblocks, you will eb fine.. just be sure to clean and scuff the entire block (dry ice blasting it prior to coating would propably do wonders for adheasion)
ive seen plenty of people painting and coating alloyblocks, you will eb fine.. just be sure to clean and scuff the entire block (dry ice blasting it prior to coating would propably do wonders for adheasion)
My sentiments exactly but I was afraid to say it! Last I checked these things are water cooled and with a properly sized radiator and airflow across it I don't see a problem. The amount of radiant heat "trapped" by the emmissive surface just translates to more load on the radiator.