LS2 402 short block at SDPC!
#343
TECH Apprentice
Join Date: Jul 2004
Location: Carolina
Posts: 375
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by CHRISPY
KJ,
What is the lead time on the standard 402 short now? (Eagle Crank, Rods, diamond pistons etc)
What is the lead time on the standard 402 short now? (Eagle Crank, Rods, diamond pistons etc)
Im about 5 weeks and waiting here. ARP main studs have been on back order and the rods were on back order or something im told which was the hold up.
#345
TECH Enthusiast
Thread Starter
iTrader: (1)
Join Date: Dec 2003
Location: Dallas, TX
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by CHRISPY
KJ,
What is the lead time on the standard 402 short now? (Eagle Crank, Rods, diamond pistons etc)
What is the lead time on the standard 402 short now? (Eagle Crank, Rods, diamond pistons etc)
****We are out of stock on the ARP main studs, and ARP says they will not start shipping again until early August We are looking into other sources now, but it doesn't look good. Please call, pm, or email me with any questions you might have. I will do all I can to make sure you get what you are looking for!!
#346
TECH Enthusiast
Thread Starter
iTrader: (1)
Join Date: Dec 2003
Location: Dallas, TX
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by MakoLS1
Im about 5 weeks and waiting here. ARP main studs have been on back order and the rods were on back order or something im told which was the hold up.
#347
Originally Posted by KJ@SDPC
I have two flat top short blocks on the shelf ready to go. I can have a dish set up put together in about two to three weeks.
****We are out of stock on the ARP main studs, and ARP says they will not start shipping again until early August We are looking into other sources now, but it doesn't look good. Please call, pm, or email me with any questions you might have. I will do all I can to make sure you get what you are looking for!!
****We are out of stock on the ARP main studs, and ARP says they will not start shipping again until early August We are looking into other sources now, but it doesn't look good. Please call, pm, or email me with any questions you might have. I will do all I can to make sure you get what you are looking for!!
#352
STF veteran / 10 second club
iTrader: (14)
Originally Posted by GuitsBoy
Yes, they seem to be working well screwed into the threaded bosses next to where the engine mounts bolt in on the side of the block.
Can you just have one knock sensor plugged into one of these bosses, or do you need to have them both?
#353
hey kris
I was just wondering, when the ls7 blocks come out and are available our you thinking about coming out with a 427 shortblock?If you could set it up the same way as this 402?(of course plus the extra cost of the block) but with all the conversion pieces I bet you could sell a ton of them
thanks matt
thanks matt
#354
hey kris
I was just wondering, when the ls7 blocks come out and are available our you thinking about coming out with a 427 shortblock?If you could set it up the same way as this 402?(of course plus the extra cost of the block) but with all the conversion pieces I bet you could sell a ton of them
thanks....... matt
thanks....... matt
#355
TECH Enthusiast
Thread Starter
iTrader: (1)
Join Date: Dec 2003
Location: Dallas, TX
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by TT_Vert
any word on a workaround for the knock sensors yet?
Dave
Dave
**Note: You will want to get some one to adjust the sensitivity when they tune your car.
#356
TECH Enthusiast
Thread Starter
iTrader: (1)
Join Date: Dec 2003
Location: Dallas, TX
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Craig@ETPerformance
KJ,
When are the LS7 intake manifolds going to be available? I have some of our heads we like to start selling for the LS7's.
Thanks,
Craig
When are the LS7 intake manifolds going to be available? I have some of our heads we like to start selling for the LS7's.
Thanks,
Craig
#358
TECH Enthusiast
Thread Starter
iTrader: (1)
Join Date: Dec 2003
Location: Dallas, TX
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by xphantomws6x
Can you just have one knock sensor plugged into one of these bosses, or do you need to have them both?
#359
TECH Junkie
iTrader: (12)
Join Date: Jul 2002
Location: Austin, TX
Posts: 3,422
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by KJ@SDPC
I have never talked to anyone that ran both on one side. I would use one on each side. I think the ecm would get a better reading!
#360
TECH Enthusiast
Thread Starter
iTrader: (1)
Join Date: Dec 2003
Location: Dallas, TX
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
Hey guys, just wanted to let you know that I just finnished putting together some iron 402's! Same rotating assembly as my LS2 set up, just using an iron block. The rings are filed to take up to 150 shot.
All five of these were built with the Callies (Comp Star) H beam rods.
Again these are on the shelf ready to ship!! Your cost is $3.549.00 + freight!!
PM, email, or call me with any questions!!
All five of these were built with the Callies (Comp Star) H beam rods.
Again these are on the shelf ready to ship!! Your cost is $3.549.00 + freight!!
PM, email, or call me with any questions!!