Vic Jr./rails/sheetmetal elbow FS
07-24-2007 | 09:20 PM
#1
Thread Starter
10 Second Club
iTrader: (12)
Joined: Nov 2001
Posts: 2,356
Likes: 1
From: Padded cell
Vic Jr./rails/sheetmetal elbow FS PICS ADDED BELOW-
I've got a new Vic. Jr, matching billet rails and an Aron's sheet metal elbow that was used for testing/R&D on my Vengeance 416 stroker.
The intake was ported by Vengeance and installed. Made 6 dyno pulls. I've decided to change directions again.
I've got $875.00 in this w/the Vengeance porting.
It's virtually brand new(already drilled/tapped for PCV/vac. lines) and available for $750.00 complete w/all hardware which is less than a bare unported FAST 90, and looks tittylicious to boot
Can be shipped immediately-
I've got a new Vic. Jr, matching billet rails and an Aron's sheet metal elbow that was used for testing/R&D on my Vengeance 416 stroker.
The intake was ported by Vengeance and installed. Made 6 dyno pulls. I've decided to change directions again.
I've got $875.00 in this w/the Vengeance porting.
It's virtually brand new(already drilled/tapped for PCV/vac. lines) and available for $750.00 complete w/all hardware which is less than a bare unported FAST 90, and looks tittylicious to boot
Can be shipped immediately-
Last edited by SLowETz; 08-16-2007 at 11:41 PM.
07-24-2007 | 10:27 PM
#3
Thread Starter
10 Second Club
iTrader: (12)
Joined: Nov 2001
Posts: 2,356
Likes: 1
From: Padded cell
Like to see it go as a complete package before it parts out as I don't need it any longer, and don't wanna be stuck w/one item I can't use or move-
If there is commitment to the intake w/rails, and elbow separately, I can do that.
If there is commitment to the intake w/rails, and elbow separately, I can do that.
07-25-2007 | 12:39 AM
#5
Please email me pictures of this. What heads was this intake ported too? jmws6@hotmail.com is the address.
07-25-2007 | 03:18 AM
#7
Joined: May 2005
Posts: 6,799
Likes: 3
From: Your girl's back door giving her the long stroke while you're at work
Does anything else have to be done to get this on a LS1 car? And do the fuel rails have the fittings on them? Shoot me some pics to usaf_firefighter@hotmail.com
Very Interested in the whole set-up!!
Very Interested in the whole set-up!!
Last edited by Z28/2002; 07-26-2007 at 01:18 AM.
Trending Topics
07-25-2007 | 10:25 AM
#10
I am interested in everything but the elbow. Please send me pics and price to romberg@ucar.edu
Send me pics of elbow too for fun.
Keith
Send me pics of elbow too for fun.
Keith
08-16-2007 | 11:39 PM
#18
Thread Starter
10 Second Club
iTrader: (12)
Joined: Nov 2001
Posts: 2,356
Likes: 1
From: Padded cell
Pics added- Still available- Pics below
This is just the intake/intake gaskets/rails/elbow, pcv/map/brake booster fittings, intake bolts, carb studs/carb gasket, and additional brackets/hardware that came with it but not needed to fit on the lsx.
No npt plugs or AN fittings included.
This intake works best on larger cubed motors with a cam matched to work with it. Also works VERY well on FI applications.
Cowl MUST be trimmed(but isn't a big deal and can be done easily).
Intake was ported by Vengeance. NOT port matched to the heads specifically, but upper/lower runners, roof-plenum area smoothed/shaped. I didn't want it port matched to the heads in the event that I changed my mind(happens more often than not-)
As stated, I'd like to ship as a package for $750.00 (plus shipping), but will part out as long as a pieces are spoken for and funds sent.
Vengeance ported Vic intake w/new FAST intake gaskets- $475.00 + shipping ($524.99 + shipping NEW)
Eddelbrock billet rails(gun metal gray powder coat)- $70.00 + shipping ($83.41 + shipping NEW)
Aaron's(Intake Elbows.com)sheetmetal elbow- $200.00 + shipping ($225.00 + shipping NEW)
This is just the intake/intake gaskets/rails/elbow, pcv/map/brake booster fittings, intake bolts, carb studs/carb gasket, and additional brackets/hardware that came with it but not needed to fit on the lsx.
No npt plugs or AN fittings included.
This intake works best on larger cubed motors with a cam matched to work with it. Also works VERY well on FI applications.
Cowl MUST be trimmed(but isn't a big deal and can be done easily).
Intake was ported by Vengeance. NOT port matched to the heads specifically, but upper/lower runners, roof-plenum area smoothed/shaped. I didn't want it port matched to the heads in the event that I changed my mind(happens more often than not-)
As stated, I'd like to ship as a package for $750.00 (plus shipping), but will part out as long as a pieces are spoken for and funds sent.
Vengeance ported Vic intake w/new FAST intake gaskets- $475.00 + shipping ($524.99 + shipping NEW)
Eddelbrock billet rails(gun metal gray powder coat)- $70.00 + shipping ($83.41 + shipping NEW)
Aaron's(Intake Elbows.com)sheetmetal elbow- $200.00 + shipping ($225.00 + shipping NEW)
