LSWHO

iTrader: (1)

and what cam and other mods?
a4/M6
stall
gears

Most I see are 110-115mph.

Bone stock heads guys. No valves, no clean up, no bowl work, stock.

Not particularly looking for ETs, but throw them out there if you like too.

Wicked94Z

iTrader: (26)

I ran 92.8 mph in the 1/8 with a CC306 cam only about 5 years ago. Mail order tune from madz28, stock 3.42 gears and 6 speed, and bfg drag radials. Probably 100 pounds less than full weight on that pass.

speed_demon24

iTrader: (6)

Impossible since off the shelf cams don't work. Hell I only have just over 2mph on that in my h/c car.

Wicked94Z

iTrader: (26)

alright fine you caught me, I spun most of 1st and 2nd gear so the mph might be slightly inflated

StealthFormula

iTrader: (35)

With my auto I trapped 110mph with a cc503 at a 3650# raceweight. Besides the cam I had full exhaust, 1.6RR's, stock converter.

robsquikz28

iTrader: (246)

full boltons, AI 226 cam, stock engine, a4, 3.23 gear on 17s and drag radial, 12.2 at 112mph

my old car ran a gm847 cam stock suspension, full bolt ons with 4.10 gear, a4 12.43 @ 107

gregrob

iTrader: (8)

107 @ 7500 da

BizZzatch350

iTrader: (33)

Seems to be the normal range for most street LT1s

LSWHO

iTrader: (1)

Yeah m6s in the high end a4s low. I'm really looking for the out of that range guys in either direction. Either what's the excuse or what's so great in their setup.

BizZzatch350

iTrader: (33)

A lot of guys post times with negative DAs but dont mention that so that may be some thing to keep in mind.

Matts94Z28

iTrader: (6)

88mph average, but I have trapped 89mph a few times in good air. cc306, bolt-ons and a PCMforless tune. 1/8th mile of course.

MPH did not change from 350ci to 355ci.

Wicked94Z

iTrader: (26)

most serious drag racers... the ones with the ability to extract exceptional results from average parts... don't mess around with cam only LT1s. Maybe 10-15 years ago, but not anymore.

speed_demon24

iTrader: (6)

Internet records are serious business.

LSWHO

iTrader: (1)

Post in the wrong thread? This has nothing to do with anything here. Clever quip though.

Wicked94Z

iTrader: (26)

only custom cams can hold records though, shelf cams are much too common and everyone would run the same time with the same cookie cutter combos.

LSWHO

iTrader: (1)

I don't give a **** about records. Stay on topic or STFU.

Since you can't read I was looking for slower than normal too. Not just the fast ones.

speed_demon24

iTrader: (6)

This is the fastest cam only lt1 I could find.

http://www.camaroz28.com/forums/show...66&postcount=1

94maro

mine went 13.1 at 110 with out the cam and rockers (cc503)(1.6)

and after the swap it went 13.001 at 110..lol i was like wtf!!!!! i beleive my heads are holding me back from letting it breath.... any input would be nice..and the 13.001 was with a 1.9 60ft street tires

StangeatinZ28

exactly what i trapped and 12.0's consistant. Vigilante 3400, 3.42's, MadZ28 mail order blah blah, AND a Comp XE 224 nyuk nyuk. My car gets out like a bat out of hell 1.7 shorts but then falls flat on its ***. The only way to wake these cars up is head work

StangeatinZ28

i would say it's almost pointless to go cam only just because there are cams that work with factory heads and then cams that work with aftermarket or ported stock castings, then you would have to change the cam to work well with the ported heads and re tune. If i could change anything i'd do matching heads/cam combo together. Buuuuttt that's just me