HELP!!! Tune for LT's?
#1
TECH Regular
Thread Starter
HELP!!! Tune for LT's?
Alright so i got my headers done about 500 miles ago, and the car has run awesome since then, but this morning it just decided to run like s***, it started with what sounded like just a few puffs every now and then at idle then it slowly got rougher and rougher at idle. Now below 2K it runs extremely rough it bucks and kinda wants to back fire and then when about 2k it evens out and runs decent.... Also when outside the car, it smells EXTREMELY rich. No idea, guys im talking too say i shouldnt need a tune. I have race headers so all the emissions are gone.
Maybe a bad o2???
Need a tune???
Need new o2s???
I did NOT put the rears back in.. i dont think i should need those, pretty sure those are just to make sure the cats are there..
Also it is an open y pipe at the moment if that matters..
Before i put on the y pipe i ran open headers for maybe 200 miles..
Im thinking its running soooo rich that it just cant run right, and then when i get a little higher in the rpms it all evens out...
Not sure at all what to do, a buddy of mine has my exact car pretty much and he did all this stuff a while ago and had zero problems that i know of..
And HELP!!!
Thanks in advance!!
Maybe a bad o2???
Need a tune???
Need new o2s???
I did NOT put the rears back in.. i dont think i should need those, pretty sure those are just to make sure the cats are there..
Also it is an open y pipe at the moment if that matters..
Before i put on the y pipe i ran open headers for maybe 200 miles..
Im thinking its running soooo rich that it just cant run right, and then when i get a little higher in the rpms it all evens out...
Not sure at all what to do, a buddy of mine has my exact car pretty much and he did all this stuff a while ago and had zero problems that i know of..
And HELP!!!
Thanks in advance!!
Last edited by 96LT1Z; 07-12-2013 at 01:51 PM.
#2
TECH Addict
iTrader: (1)
Yea, you need a tune to get the proper gains out of headers ASAP. As for the gas smell running like crap, does it make any difference if the car is in open or closed loop? It's also possible your O2's are messed up....were they coated headers? That coating has been known to burn off and cause O2 issues. Also, are you absolutely sure there's no exhaust leaks? Hear any puffing or ticking sounds? Headers on these cars are notorious for leaking, which will make it run rich and get shitty mileage. Are you getting any codes?
#3
TECH Regular
Thread Starter
Im pretty sure there isnt any exhaust leaks off the head, but il check again. But the puff sound i was talking about i am %100 positive it was coming out of the end of the y pipe. I just sounded like it was pushing air.. and it was doing that right before it started running shitty
#4
TECH Regular
Thread Starter
There a painted pacesetters and then i painted them with high temp paint..
And then im not sure on the open or closed loop, how do i know tje difference?
How do i know if the o2s are bad??
And then im not sure on the open or closed loop, how do i know tje difference?
How do i know if the o2s are bad??
#6
TECH Regular
Thread Starter
What collector? Im running an open y pipe right now.. if thats what your thinking of. If your talking about the header to the y, there isnt any leak there.
Also i WILL check all of this but, would this cause it to run like *** below 2k then run good above that???
Also i WILL check all of this but, would this cause it to run like *** below 2k then run good above that???
#7
TECH Addict
iTrader: (1)
If you scan the car, you should be able to see the O2 sensor reading fluctuate back and forth (in closed loop)....not stuck on a certain voltage. Good luck!
Trending Topics
#8
TECH Addict
iTrader: (1)
LMAO....your running an open Y-pipe and wonder why your car runs like ***? Every header has a collector...it's where the header primarys merge to meet the y-pipe. Get an exhaust system dood! Of course it's gonna run like *** with a half assed incomplete exhaust system...LOL.
#9
TECH Regular
Thread Starter
Shitt.... Lol alright good thing its going in to get welded in a couple days..
Alright and as for the open closed loop, it runs fine when its from a cold start up, its when it warms up it runs rough
Alright and as for the open closed loop, it runs fine when its from a cold start up, its when it warms up it runs rough
#12
Just an idea, but maybe check for a burned plug wire touching one of the headers. I had that randomly happen with my car with manifolds on. The car was running great and then all of the sudden started running horrible. After a ton of trouble shooting found one of the plug wires sitting right against the manifold.
#13
11 Second Club
O2's just hate longtube headers for some reason. Maybe cause there not getting hot enough? Idk..
#14
TECH Regular
Thread Starter
Ya idk, im getting the exhaust welded up tomorrow, and the o2 should be here friday sooo cross my fingers!
Anyways since i have to wait on all this stuff iv been driving it lately and it drives fine when you get going! i just hates idling and starting from a stop... lol but i drove it about an hour both ways on the interstate today and it ran great or than when in 6th at about 1500k then i sputtered a bit
Anyways since i have to wait on all this stuff iv been driving it lately and it drives fine when you get going! i just hates idling and starting from a stop... lol but i drove it about an hour both ways on the interstate today and it ran great or than when in 6th at about 1500k then i sputtered a bit
#18
TECH Regular
Thread Starter
#19
TECH Fanatic
iTrader: (2)
Join Date: Dec 2010
Location: Oklahoma
Posts: 1,084
Likes: 0
Received 0 Likes
on
0 Posts
It could be the o2 sensor/s. Make sure that you don't have Bosch o2 sensors. They plain suck. Seems that with it running better after you get into higher rpms that the sensors have gone bad or the wires for the sensors have gotten too close to the header and melted together. Did you use premade extensions or extend the wires yourself? It doesn't have a mis or anything, just runs like crap until you get on it?
#20
TECH Regular
Thread Starter
It could be the o2 sensor/s. Make sure that you don't have Bosch o2 sensors. They plain suck. Seems that with it running better after you get into higher rpms that the sensors have gone bad or the wires for the sensors have gotten too close to the header and melted together. Did you use premade extensions or extend the wires yourself? It doesn't have a mis or anything, just runs like crap until you get on it?