View Poll Results: What engine would you go with
Voters: 229. You may not vote on this poll
What Engine would you get?
#21
11 Second Club
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I'd have to go with a choice not on your list...
BBC, with a decent shot on top of that...
Oh wait that is what I am getting pricing on right now and will build up over the next few years...
BBC, with a decent shot on top of that...
Oh wait that is what I am getting pricing on right now and will build up over the next few years...
![Happy](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_stretch.gif)
#23
TECH Enthusiast
Join Date: Feb 2007
Location: Seattle area
Posts: 686
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Now if I could get this motor to fit, then I would be in heaven. Then again it may fit in a C3!
Engine displacement: 780 cui (12.9 L)
Compression ratio: 11.5: 1
Cylinders: V / 8
Including:
-especially machined distortion free high-precision cylinder block
-individually machined high-precision crankshaft each crankshaft is fine-balanced using master weights (counter weights simulating the weights of the pistons and connecting rods which are installed later). A more exact balancing of the crankshaft is not possible!!!
-lowest crankshaft bearing tolerance Crankshaft pins are smoothed to an accuracy of 5 thousandths of a millimetre-which allows for extremely high revolution rates!!!
-super high-performance Weineck pistons
-endless piston rings (to prevent the combustion energy from bypassing the piston)
-super high-performance Weineck connecting rods
-individually machined high-performance cylinder heads All cylinder heads are prepared with a 16-knife milling head to ensure the same surface quality throughout the milling process
-individually machined high-performance valve seats. All valve seats are milled with an accuracy of up to the hundredth part of a millimetre and all three valve seat angles are milled in a single operation
-individually engineered and machined high-performance lightweight titanium valves - individually handmade, super high-performance exhaust manifolds (headers)
-super high-performance exhaust system
-super high-performance engine oil cooling system
-super high-performance gearbox oil cooling system
-
-super high-performance rear differential oil cooling system
-super high-performance ignition system (fully digital) with rev. limiter
Max. power: 809 kW / 1,100 hp at
7,000 rpm.
Max. torque: 1,760 Nm at 5,600 rpm.
Engine displacement: 780 cui (12.9 L)
Compression ratio: 11.5: 1
Cylinders: V / 8
Including:
-especially machined distortion free high-precision cylinder block
-individually machined high-precision crankshaft each crankshaft is fine-balanced using master weights (counter weights simulating the weights of the pistons and connecting rods which are installed later). A more exact balancing of the crankshaft is not possible!!!
-lowest crankshaft bearing tolerance Crankshaft pins are smoothed to an accuracy of 5 thousandths of a millimetre-which allows for extremely high revolution rates!!!
-super high-performance Weineck pistons
-endless piston rings (to prevent the combustion energy from bypassing the piston)
-super high-performance Weineck connecting rods
-individually machined high-performance cylinder heads All cylinder heads are prepared with a 16-knife milling head to ensure the same surface quality throughout the milling process
-individually machined high-performance valve seats. All valve seats are milled with an accuracy of up to the hundredth part of a millimetre and all three valve seat angles are milled in a single operation
-individually engineered and machined high-performance lightweight titanium valves - individually handmade, super high-performance exhaust manifolds (headers)
-super high-performance exhaust system
-super high-performance engine oil cooling system
-super high-performance gearbox oil cooling system
-
-super high-performance rear differential oil cooling system
-super high-performance ignition system (fully digital) with rev. limiter
Max. power: 809 kW / 1,100 hp at
7,000 rpm.
Max. torque: 1,760 Nm at 5,600 rpm.
![](http://www.exoticcarsite.com/pictures/tuners/weineck/cobra-780-cui/weineck-cobra-780-cui-limited-edition-20.jpg)
#24
Launching!
iTrader: (2)
Join Date: Jun 2006
Location: fresno, ca
Posts: 278
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
if money wasnt an issue, id want a stroked and blown ls2. have you guys seen the GTO that MTI built? its a 455 with a rear-mounted turbo. id want something like that but with TTs. a part of me wants a 396 lt1 with a nasty head and cam package though.
#25
11 Second Club
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by Captainofiron
haha nice BBC, I would like to pics of that, especially how you get that Rat to fit in there
#29
11 Second Club
iTrader: (88)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by VinR1
I'd get World Product's tall deck LSX block - 482ci, a set of their heads or some LS7s with a good port and a nice lumpy cam... 700hp shouldnt be too hard to come by with that combo
![EEK !!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_eek2.gif)
I would go with a LS7 and Cam the hell out of it.. I say that cause I already have the Wiring Harness built for a LSX Engine.
I am building a 402, wish I had some free money for that..
![The Jester](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_jest.gif)
#35
Teching In
Join Date: Mar 2007
Location: Seymour Johnson
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
This is what I would be getting if money were no object!!
http://lingenfelter.com/Lingenfelter...boCorvette.htm
http://lingenfelter.com/Lingenfelter...boCorvette.htm
#40
TECH Fanatic
iTrader: (17)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by the_merv
That's insane...
Any links to that beast, I want to see that.
I would go with a LS7 and Cam the hell out of it.. I say that cause I already have the Wiring Harness built for a LSX Engine.
I am building a 402, wish I had some free money for that..![The Jester](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_jest.gif)
![EEK !!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_eek2.gif)
I would go with a LS7 and Cam the hell out of it.. I say that cause I already have the Wiring Harness built for a LSX Engine.
I am building a 402, wish I had some free money for that..
![The Jester](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_jest.gif)
http://www.worldcastings.com/prods_pages/086210.htm
they're still working on the heads