Stang-Slayer

iTrader: (16)

ehhhh i see....lol i guess that reverse lockout could be kind of important ahaha
going 65 and accidentally stick it in reverse hahahaha

the_merv

iTrader: (88)

Well you are thinking of it opposite of how it actually is..then again from the way I said it, that didn't help either.

What I meant by function was that when you tune it, under 3mph it will open the Solenoid and allow you to go into Reverse easier, instead of have to force it in. It is blocked out of Reverse unless it gets the signal to open the Solenoid.

Stang-Slayer

iTrader: (16)

Is it managable to drive at least for a little while though like that?
U think you could dmg something forcing it like that?

the_merv

iTrader: (88)

It's manageable, I don't think you could damage anything..

Black02SLPSS

iTrader: (5)

Well, im in the process of swapping out my a4 harness to an m6 harness. I completed the A4-M6 swap last year, and im curious about what the m6 harness will bring back. For whatever reason my cruise control does not work. Will putting in an M6 harness make my reverse lights work, reverse lockout work and cruise work? Im pretty sure it will make the reverse lights and lock out work but what about the cruise? If not what do i need to do to make it work? Oh and how hard does everyone think it would be to swap an a4 interior harness to the m6 interior harness? I guess the underdash harness?

bjamick

iTrader: (31)

Everything will work just as its supposed it. You have changed your car completely to an M6 now and the harness will have everything on it such as the skip shift, reverse lock-out, cruise control will work all that good stuff.

Black02SLPSS

iTrader: (5)

Sweet! Thanks for the good news answer.

the_merv

iTrader: (88)

There is a Switch on the 1999 and up cars that goes on the Clutch Petal, it's called the Clutch Anticipation Switch. I know that one function of that is to turn the Cruise off, but you can actually wire that without that particular switch. PM me and I can explain it.

Engine_HP

iTrader: (1)

WHY the PM say it in public im also interested.

bjamick

iTrader: (31)

Hey Merv or anyone, it wont hurt the performance if I dont write entire will it? My tuner just changed it to where the speedo would read right and turned off most of the auto stuff to keep the ses light off. What you think?

93cz28

iTrader: (5)

just finished the swap and my gauge cluster fuse blows everytime i put it into reverse.i used an m6 harness and when i put it into reverse the backup lights dont come on either. im guessing the 2 wires that were left over (green and brown) in the center console should go in place of the backup light wires on the tranny, because if i touch them together my back up lights come on. also its hard to get the car into gear when i turn it on. think i need to bleed the hydraulics a bit more?

bjamick

iTrader: (31)

You can try the rev test to see. Rev it up in 1st gear and see if the car will move. That will tell you if it needs bled. Ya those wires go to the reverse switch.

93cz28

iTrader: (5)

yea the car moves in first and all the gears go in fine now except reverse.i can put it into the gate but it just wont go in reverse. also the car wont start unless i jump start it. somethng is massively draining the battery really quick.and when i do turn it on it runs but then turns off while in neutral and wont turn on again.

93cz28

iTrader: (5)

alright everything works great now. i have 1 suggestion about using an m6 harness.cut off the pigtail for the back lights off of the harness and cover up those 2 wires. elongate the 2 backup light wires from inside the car and solder on the pigtail. run that down and connect it to the back up light connection on the tranny. if you dont do that your gonna 1. blow your gauge fuse 2.drain your battery 3. your back up lights wont work. the only other wiring you would have to do if you use an m6 harness is solder the 2 wires inside the car for the hatch release together, and elongate the clutch switch wires and attach them to the black switch on your clutch. everything else is just plug and play.

the_merv

iTrader: (88)

^^Cutting off that Pig Tail depends on the Car.. I wired mine in as it was factory and extended the Reverse Light wire over to it. I used the Auto Trans Power Wire that was in the Harness to power that circuit.

Devils Mentor

iTrader: (20)

I will be doing a A4 to M6 swap soon so I need to reread this, but I thought I would ask.... Is there anyone here that is from Jacksonville Florida, or at least close that would be willing to help or for a fee, do the swap?


Thanks guys!!!


DM

indirocz28

iTrader: (7)

If anyone is looking for a good Lsx 4l60e i have a very clean low mileage one out of a 2wd truck that was wrecked. 20,000miles on it....

Can send pictures.. I dont need it anymore i got rid of my lsx car- and this things just taking up space i really dont have..

$450 obo...
Will ship at your expense..

MBC Racing

iTrader: (3)

so is the harness the COMPLETE engine wiring harness?
OR is there just a portion of it you can replace?

Looks like there are enough people switching from A4 to M6 and M6 to A4 to be able to just trade harnessses???

I am planning on M6 to A4, but was hoping to keep the pedels incase I ever go back..... Oh well. Maybe just easier to find someone do the opposite of what I am and trade out some pieces.

Anybody in IL doing this?

Thanks

K6Ls1

I would like to go to M6, but I'm in Georgia.

Anyone for a complete swap of my A4 for your M6, in GA?

30th t/a

iTrader: (51)

A4 to M6 swap below.
http://www.gmhightechperformance.com...wap/index.html