Tips for hillbilly tranny removal...
#1
TECH Fanatic
Thread Starter
iTrader: (1)
Join Date: Aug 2006
Location: DE La Ware
Posts: 1,094
Likes: 0
Received 0 Likes
on
0 Posts
Tips for hillbilly tranny removal...
Well Im sure plenty of you guys have pulled trannys without the proper tools. What are some tips for a garage job? I have some pretty tall jack stands with a decent jack but no tranny jack. Also doin the rearend at the same time but that shouldnt be too difficult. Any help would be appreciated.
Thanks,
Erik
Thanks,
Erik
#2
TECH Addict
iTrader: (7)
Getting some LONG *** extensions to remove the top bolts from the tranny to the bellhousing will come in very handy. If you have the car high enough, a regular or low-profile jack will be helpful when dropping the tranny as it's pretty heavy, especially when you're on your back. I recommend having a friend with you.
#3
Internet Mechanic
iTrader: (17)
Getting some LONG *** extensions to remove the top bolts from the tranny to the bellhousing will come in very handy. If you have the car high enough, a regular or low-profile jack will be helpful when dropping the tranny as it's pretty heavy, especially when you're on your back. I recommend having a friend with you.
#4
yeah they weigh about 175-200 without fluid, i just yanked it out let it down on my chest and rolled it off... not too bad, just get it as high as you can on the stands and yeah u are gonna need some long extensions. if you dont know already it is a shitload easier if you separate the trans from the bell housing first
#5
Getting some LONG *** extensions to remove the top bolts from the tranny to the bellhousing will come in very handy. If you have the car high enough, a regular or low-profile jack will be helpful when dropping the tranny as it's pretty heavy, especially when you're on your back. I recommend having a friend with you.
Trending Topics
#8
yeah they weigh about 175-200 without fluid, i just yanked it out let it down on my chest and rolled it off... not too bad, just get it as high as you can on the stands and yeah u are gonna need some long extensions. if you dont know already it is a shitload easier if you separate the trans from the bell housing first
#9
10 Second Club
Join Date: Nov 2002
Location: Berkeley, California
Posts: 1,471
Likes: 0
Received 3 Likes
on
3 Posts
The Harbor Freight Transmission Jack is very inexpensive and greatly simplifies the job.
http://www.harborfreight.com/cpi/cta...emnumber=39178
http://www.harborfreight.com/cpi/cta...emnumber=39178
#10
well you just have to use common sense, if you can bench 175-200 at least you will be fine. i would reccomend having a friend, but if you need it out and your alone you should be okay...
#13
TECH Fanatic
Thread Starter
iTrader: (1)
Join Date: Aug 2006
Location: DE La Ware
Posts: 1,094
Likes: 0
Received 0 Likes
on
0 Posts
Thanks guys,
Benching it down shouldnt be a problem. Gettin it back up might be. First thing though is cleanin the damn garage. I hate losing things under trash or paper towels. Stuff rolls under damn things 20ft away when it could just stay where it should... oh well. If I need to I could prob rig the jack to get it back up in place.
Benching it down shouldnt be a problem. Gettin it back up might be. First thing though is cleanin the damn garage. I hate losing things under trash or paper towels. Stuff rolls under damn things 20ft away when it could just stay where it should... oh well. If I need to I could prob rig the jack to get it back up in place.
#16
gettin it back up requires some finesse, i usually just put a piece of wood on my jack plate to keep it even when im jacking it up, you might wanna use just a little bit of grease on the dowel pins so the bell housing isnt such a bitch to get off next time.
#20
don't let this guy think he can do it if he can't, they weight more than 135 for sure buddy