NEW!! LS2 Plate install Picture
01-26-2006, 06:09 PM
#1
TECH Resident
Thread Starter
iTrader: (1)
Join Date: Jan 2005
Posts: 909
Likes: 0
Received 0 Likes
on
0 Posts
NEW!! LS2 Plate install Picture Thought you guys might like to see the Cold Fusion LS2 Plate Installed, it's really a sweet setup!
100-250HP on Single Stage
and on the Dual Stage
100-250HP for Each stage for a combined 200-500HP
Available in a complete kit
Kit with no Bottle, Bracket or Feedline
And Just the Plate
100-250HP on Single Stage
and on the Dual Stage
100-250HP for Each stage for a combined 200-500HP
Available in a complete kit
Kit with no Bottle, Bracket or Feedline
And Just the Plate
Trending Topics
02-15-2006, 07:13 PM
#10
Staging Lane
Join Date: Dec 2005
Location: Tomball, Texas
Posts: 88
Likes: 0
Received 0 Likes
on
0 Posts
LS2 plate
Originally Posted by 1MEANGTO
How much is just the plate????
Contact Scott at Nitrous Direct He can get you anything you need. If you decide to get one and take some good pics Scott has been known to give you an extra killer deal.
02-16-2006, 01:13 PM
#13
FormerVendor
Join Date: Apr 2005
Location: Wichita Falls,Tx
Posts: 864
Likes: 0
Received 0 Likes
on
0 Posts
Good looking install. How's the spray pattern? Is it spraying from the top, down into the incoming air? Or is it spraying all around the perimeter? Nice design with putting the inlet up top.
02-16-2006, 11:48 PM
#15
Originally Posted by NXJeremy
Good looking install. How's the spray pattern? Is it spraying from the top, down into the incoming air? Or is it spraying all around the perimeter? Nice design with putting the inlet up top.
Robert
02-17-2006, 08:35 AM
#16
Staging Lane
Join Date: Dec 2005
Location: Tomball, Texas
Posts: 88
Likes: 0
Received 0 Likes
on
0 Posts
Yes, it does spray from the top out at many different angles. The design allows it to fan wide and cover all of the ports very well. Works killer. Makes serious power!!!
02-17-2006, 09:37 AM
#17
FormerVendor
Join Date: Apr 2005
Location: Wichita Falls,Tx
Posts: 864
Likes: 0
Received 0 Likes
on
0 Posts
Thanks Albert. So there are multiple holes along the top portion of the plate orifice, or is there just one or two holes that spray the nitrous and fuel similar to a fan type nozzle? I couldn't tell from the pics above. Thanks.
Robert, start using your pull around there and get a plate your own car, lol.
Robert, start using your pull around there and get a plate your own car, lol.
Last edited by NXJeremy; 02-17-2006 at 09:42 AM.
02-19-2006, 08:12 PM
#19
Originally Posted by NXJeremy
Thanks Albert. So there are multiple holes along the top portion of the plate orifice, or is there just one or two holes that spray the nitrous and fuel similar to a fan type nozzle? I couldn't tell from the pics above. Thanks.
Robert, start using your pull around there and get a plate your own car, lol.
Robert, start using your pull around there and get a plate your own car, lol.
Robert
02-19-2006, 08:44 PM
#20
So if you have a leaking fuel solenoid, fuel can drip from plate at idle, drip from plate engine off, and drip at low rpm cruise. Causing the excessive fuel to gather (puddle) in the intake plenum area and backfire could/will occur. How does one check for a leaking fuel solenoid?