Kingc8r

iTrader: (21)

So do I need one or I don't need to worry since I have the mini controller?

Roger Z06

iTrader: (4)

This is very helpful

Roger Z06

iTrader: (4)

I mean the diagrams when hooking up your own kit

04RedGTO

I saw earlier in the thread that this was posted.

I have a 04 6 speed GTO and I want to get the TPS and RPM from under the dash. I believe that these connectors mentioned above are under the drivers kick panel. Anyone ever tap into these wires? Pics would be great.

Also, can I get some help with a wiring diagram.

My setup consists of a Nitro Dave window switch/ tps switch. Nitro Dave dry kit w/ halo bar. NX Bottle opener. FPSS. Nos bottle heater that is thermostatically controlled. 4 button switch panel that goes in cubby under radio.

stewaj11

iTrader: (5)

Is there a wiring diagram for what I will be installing in the next couple weeks? It is a wet system with a single bottle, 2 flip switches for arming the system, relay for the solenoids, a WOT switch and bracket, the solenoids (fuel and N2O) and 75 shot jet... Any help would be appreciated greatly

Thule

i am wiring my plate kit, need to take signal from one of the front 02sensors

what pin?

1. TAN HO2S Signal Low Bank 2 Sensor 2
2. TAN/WHT HO2S Signal Low Bank 1 Sensor 2

5. TAN HO2S Signal Low Bank 2 Sensor 1
6. TAN/WHT HO2S Signal Low Bank 1 Sensor 1
-----------------------------------------------
41. PPL HO2S Signal High Bank 2 Sensor 2
42 PPL/WHT HO2S Signal High Bank 1 Sensor 2
46. PPL HO2S Signal High Bank 2 Sensor 1
47 PPL/WHT HO2S Signal High Bank 1 Sensor 1

?

Fondle

iTrader: (4)

anyone know what color the tps wire on a 99 v6 camaro is?

Ego Killer

iTrader: (147)

anyone have a diagram for a
Harlan 2 step
trans break
nitrous?

SStriker

iTrader: (3)

I need help with a wiring diagram for a MSD 8969 WS. I already have a HSW we kit, with a WOT switch hooked up. I just need help with the WS.
Thanks in advance.

OHH RLY?

iTrader: (3)

Hey guys, I need help with this diagram:

http://www.fquick.com/garages/viewga...ewimg&id=46684

I cannot read the print at all. Basically I took my console out to adjust my shifter stiffness and the stops but had to disconnect my arming/heater/purge/bottle opening switches and now none of the wires are hot. I also tried to find a fuse inline to the relay and also got nothing. If anyone can help me I would appreciate it!

Blake

yak

iTrader: (15)

Need some help, I'll delete this once a diagram gets posted.

Wet kit
Dry kit
T brake
MSD window switch
WOT switch
Purge
one arming switch for each kit.
Is it possible to piggyback both kits to the window switch?

04SVTL

I need a diagram for a NX kit with a purge and bottle heater. Also using a FJO progressive controller. I want to run relays in the circut, Should I run a relay for each acc.?

05gmc

iTrader: (34)

i need a little help, i have a 2002 trans am with a digital MSD window switch and when i set it to shut off @ 3000 rpms i seems like its still spraying is there a way to hook up my zex WOT switch to turn the system off when i let off the throtle.

TX RED

iTrader: (19)

I have a NX wet kit
zex traction control
and a nitrous outlet stand alone

mitch cobb racing

iTrader: (2)

i might have missed it somewhere, but can i get a diagram for a brand-x single nozzle kit, NO heater, brand-x purge and NO dual stage window switch. thanks!

Ray@Nitrous Outlet

check out the link in my signature and you should find what you are looking for

mitch cobb racing

iTrader: (2)

thanks, never noticed that link before.

LIL SS

iTrader: (9)

Anything for:

2 stage with arming switch for both stages
Throttle switch
FPSS and Harlan window switch hanging off the grounds for both stages of n20

Bellow is a diagram I put together and tested with out the window switch attached. I put the wire from the FPSS to the window switch straight to ground for the test so I didn't have to rev the motor and have my buddy listen for clicking niods.

I thought I had it figured out tonight until arming either stage activated their appropriate noids. We disconnected the throttle switch thinking we might have a faulty ground and it still was firing the noids for both systems individually when armed. Tracing it down to the switches. It seems due to the light in the switches and requiring a ground, when armed it's firing the noids. doesn't seem right though.. Am I over looking something?

ls2_fast

Anyone happen to have an NX single wet kit with a mallory window rpm switch (pn.628)

garage_queen

iTrader: (3)

EDIT: Nevermind, I found info on the MSD site stating that the 8680 cannot be used in this way.

How about one with MSD 6AL, MSD 8680 retard, MSD 8956 window switch, single stage? I only want the MSD 8680 to be active with the nitrous so I can set the **** and have it pull timing for n2o but not when going n/a.