Problem with wet shot..
Problem with wet shot.. This is my set-up..
2000 TA with NOS wet kit, fpss, wot switch, and timing tuner.
My problem is that when the nitrous activates its almost like its cutting on and off. When I had a 50 shot or so in there it didnt do it, but when I put the 75 in it started.
2000 TA with NOS wet kit, fpss, wot switch, and timing tuner.
My problem is that when the nitrous activates its almost like its cutting on and off. When I had a 50 shot or so in there it didnt do it, but when I put the 75 in it started.
Guest
Posts: n/a
Have you checked your fuel pressure....
What plugs are you using...
How much timing are you pulling if any....
Do you know what your A/F is....
it sounds like the FPSS is shutting the system down...but the above questions will help us figure it out
What plugs are you using...
How much timing are you pulling if any....
Do you know what your A/F is....
it sounds like the FPSS is shutting the system down...but the above questions will help us figure it out
I'm not too sure what the fuel pressure is, but I'm running TR6's with .36 gap. I'm pulling out 3 degrees of timing. By monitoring the narrowband O2's they were showing around .920-.940 mv.
The car is full bolt-ons with TR224 cam.
The car is full bolt-ons with TR224 cam.
YES...get it in the hot tub and warm it to about 900 then go try and see if it does it again...if not then it was just low pressure, next time warm it to 1050 and you really get the full potential out of it, i say try it at 900 first so your still rich but not enough to pop
(pressure will drop about 100 when you open the bottle and fill the line...
(pressure will drop about 100 when you open the bottle and fill the line...
Your running a FPSS and don't know what your fuel pressure is? 
Chances are thats it right there.
Monitor your pressure during a pull, and compare that to what your fpss is set to.
As far as 500 psi, thats wothless as well. Shouldn't surge though unless you just ran out.
Vinny
Chances are thats it right there.
Monitor your pressure during a pull, and compare that to what your fpss is set to.
As far as 500 psi, thats wothless as well. Shouldn't surge though unless you just ran out.
Vinny
Trending Topics
Guest
Posts: n/a
Since you don't know what your fuel pressure is doing you might try readjusting your FPSS.....
Remove the bottle from the car......Take the fuel line off the nozzle....have an assistent hold the fuel line into a catch can.....bring the vehicle up within the RPM window and activate the kit......slowly tighten the adjusting screw until the sytem starts to pulse/shut down, then back the screw off 3/4 of a turn.
Remove the bottle from the car......Take the fuel line off the nozzle....have an assistent hold the fuel line into a catch can.....bring the vehicle up within the RPM window and activate the kit......slowly tighten the adjusting screw until the sytem starts to pulse/shut down, then back the screw off 3/4 of a turn.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Originally Posted by Ray@Nitrous Outlet
Since you don't know what your fuel pressure is doing you might try readjusting your FPSS.....
Remove the bottle from the car......Take the fuel line off the nozzle....have an assistent hold the fuel line into a catch can.....bring the vehicle up within the RPM window and activate the kit......slowly tighten the adjusting screw until the sytem starts to pulse/shut down, then back the screw off 3/4 of a turn.
Remove the bottle from the car......Take the fuel line off the nozzle....have an assistent hold the fuel line into a catch can.....bring the vehicle up within the RPM window and activate the kit......slowly tighten the adjusting screw until the sytem starts to pulse/shut down, then back the screw off 3/4 of a turn.
Originally Posted by Ray@Nitrous Outlet
Since you don't know what your fuel pressure is doing you might try readjusting your FPSS.....
Remove the bottle from the car......Take the fuel line off the nozzle....have an assistent hold the fuel line into a catch can.....bring the vehicle up within the RPM window and activate the kit......slowly tighten the adjusting screw until the sytem starts to pulse/shut down, then back the screw off 3/4 of a turn.
Remove the bottle from the car......Take the fuel line off the nozzle....have an assistent hold the fuel line into a catch can.....bring the vehicle up within the RPM window and activate the kit......slowly tighten the adjusting screw until the sytem starts to pulse/shut down, then back the screw off 3/4 of a turn.
i also have a buddy with an lt1 trying to spray a 1oo shot and is have the same problem only his bottle pressure is higher, he doesnt have a fpss, and it also feels like it is miss firing when he sprays it. what you guys think about this problem?
Guest
Posts: n/a
Originally Posted by c5formula
i also have a buddy with an lt1 trying to spray a 1oo shot and is have the same problem only his bottle pressure is higher, he doesnt have a fpss, and it also feels like it is miss firing when he sprays it. what you guys think about this problem?
Originally Posted by Ray@Nitrous Outlet
Have you checked your fuel pressure....
What plugs are you using...
How much timing are you pulling if any....
Do you know what your A/F is....
What was the bottle pressure...
What plugs are you using...
How much timing are you pulling if any....
Do you know what your A/F is....
What was the bottle pressure...
sorry guys I had to.
P.S. I have an LT1
We will also need to know the current mod status.
Please find out the above information and we will be happy to help diagnose his issues.
ok the lt1 has p&p heads, p&p intake, 230-565 cam, full intake, full exhaust, ngk tr7, comp is around 11.5.1, 4.10s, msd blaster coil, mallory highfire 687 ign box, 1.6 rrs, harris speed works wet shot. bottle preasure was around 900psi, fuel preasure is around 45psi the whole time. when you first hit it, it feels like it is about to start hauling butt, but then the power feels like it drops maybe lower than what it is on motor. also starts to feel like it is missing.
Guest
Posts: n/a
Originally Posted by c5formula
ok the lt1 has p&p heads, p&p intake, 230-565 cam, full intake, full exhaust, ngk tr7, comp is around 11.5.1, 4.10s, msd blaster coil, mallory highfire 687 ign box, 1.6 rrs, harris speed works wet shot. bottle preasure was around 900psi, fuel preasure is around 45psi the whole time. when you first hit it, it feels like it is about to start hauling butt, but then the power feels like it drops maybe lower than what it is on motor. also starts to feel like it is missing.
On the miss, is it back firing/popping out the exhaust?
sorry for all the questions but the more information you give the more we can narrow it down.
on motor the timing is set at 34 but for some reason it pulls 3 out under wot on motor. when i spray it im pulling 4. so when im spraying it, its like its pulling 7 out i guess. the tr7s are gapped at like 25 or 26. i had some tr6 in there gapped at like 35 or 36 and still does the same thing on the tr7 that it did on the tr6. im not sure of how to check the plugs for detination. the hsw kits are rated for 900 psi. how do i verify the miss?
oh and this is c5formula
oh and this is c5formula
Guest
Posts: n/a
Originally Posted by Phlip00WS6
on motor the timing is set at 34 but for some reason it pulls 3 out under wot on motor. when i spray it im pulling 4. so when im spraying it, its like its pulling 7 out i guess. the tr7s are gapped at like 25 or 26. i had some tr6 in there gapped at like 35 or 36 and still does the same thing on the tr7 that it did on the tr6. im not sure of how to check the plugs for detination. the hsw kits are rated for 900 psi. how do i verify the miss?
oh and this is c5formula
oh and this is c5formula
if the car is pulling timing on motor...you have issues that need to be resolved with your current tune/tune up....the car needs to be set up w/no knock retard for an NA pass. It could be false knock but it is a risk I would not take.
Once you get that resolved you should be able to run the TR-6's gapped at .035 and pull 2-3* for a 100 shot.
PM sent....