Updated! LS parts! coils, LS7 clutch, spec clutch, push rods, valve covers, ETC!
03-19-2011, 09:45 PM
#1
TECH Resident
Thread Starter
iTrader: (47)
Join Date: Apr 2007
Location: Aurora, CO
Posts: 867
Likes: 0
Received 0 Likes
on
0 Posts
Updated! LS parts! coils, LS7 clutch, spec clutch, push rods, valve covers, ETC! Category: Engine - Power Adders
Price: $1
Part Fits: 2010+ Camaro, 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird, Corvette, 04-06 Pontiac GTO, 04+ Cadillac CTS-V
Location (State): CO
Item Condition: Used
Shipping Information: Item Can be Shipped
Engine: LS2/LS3/LS7/L92/LS9, LS1/LS6
LS Engine?: Non-LS Part
-full set of round high output coils with brackets, sold!
-full set of AFR dual spring titanium retainers, just the retainers, 30.00 shipped??
-spec stage 3+ 99-06 silverado v8 5spd clutch, with nv 3500 trans, springs in disc started to come out due to pilot bearing failure, has 2k on it! went to 4l80e, you could buy just a disc and save some money, or run the HD pressure plate with a new stock disc, SOLD!
-full set of ls7 valve springs with 6k, sold!
-LQ4 maf, good working condition, 50.00 shipped!
-one stock 09 LS7 C6 ZO6 rear axle with 2k on it, slight crack in outer grease boot, great spare, basicly new, i could even re-boot it if need be, 100.00 shipped!
-99-03? silverado fuel pump assy with sending unit, 40.00 shipped!
-(3) sets of 6.0L exhaust manifolds, best manifold for DIY turbo setups, 75.00 shipped per set!
-one set of truck manifold outlet flanges, great for for DIY turbo setups, 35.00 shipped!
-(2) 90mm DBW 4 bolt truck throttle bodies, 50.00 shipped each!
-dbw 78mm truck throttle body, 45.00 shipped!
-99-04? gm truck/suv alternator, 105amp, 60.00 shipped!
-set of 09 ls valve covers, will clear ls3/l92 rockers, like new, 65.00 shipped!
-gen 5 (ls4, ls2, ls3, l92, etc.) knock sensors and pigtails, 45.00 shipped!
Last edited by 89LS1FOXER; 05-04-2011 at 02:26 PM.
03-20-2011, 09:36 AM
#3
Teching In
iTrader: (2)
Join Date: Sep 2008
Location: Greenville SC
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
Bump for ed Curtis custom cam. I contacted him for a custom one in my current 370 and he nailed it power and drivability wise I will never go with an off the shelf cam again
03-20-2011, 11:40 AM
#4
TECH Resident
Thread Starter
iTrader: (47)
Join Date: Apr 2007
Location: Aurora, CO
Posts: 867
Likes: 0
Received 0 Likes
on
0 Posts
i think it was a all motor cam, i know the guy that i got it from was making 350 rwhp with a 4.8l using it. It has a split too so it would work for nitrous also.
morning bump!!
morning bump!!
