FS: 1998 Z28 Camaro Complete Part Out
#1
TECH Apprentice
Thread Starter
iTrader: (2)
Join Date: Aug 2008
Location: Irvine, CA
Posts: 344
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Category: Interior
Price: $0
Location (State): CA
Item Condition: Used
Shipping Information: Item Can be Shipped
Engine: LS1/LS6
LS Engine?: Fits LS Engine
I am located in Irvine, CA.
*Note*
If you do not include an offer or ask for something that's already been stated as not available, I will not respond.
Here are some quick pictures.
![](http://www.wannaberacer.com/misc/camaro.jpg)
![](http://www.wannaberacer.com/misc/camaro2.jpg)
![](http://www.wannaberacer.com/misc/camaro3.jpg)
![](http://www.wannaberacer.com/misc/camaro4.jpg)
![](http://www.wannaberacer.com/misc/camaro5.jpg)
-Don
Donathon@gmail.com
Last edited by Don Nguyen; 06-30-2011 at 02:11 AM.
#3
TECH Apprentice
Thread Starter
iTrader: (2)
Join Date: Aug 2008
Location: Irvine, CA
Posts: 344
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I believe so. Pulled it out earlier. Had to cut it from where it bolts to mid pipe. I still have the piece that I cut, so it can be rewelded back on if necessary.
I'll take better pictures of it tomorrow.
-Don
I'll take better pictures of it tomorrow.
-Don
#8
TECH Apprentice
Thread Starter
iTrader: (2)
Join Date: Aug 2008
Location: Irvine, CA
Posts: 344
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
To me, it's worth as if I didn't have to cut off the flange. Not sure if it is worth it for you to have me ship such a large piece to you.
If really needed, I can have it welded back on. However, the bolts are rusted to the section that I cut off from the mid pipes. I also do not know/see how it'd even be possible to reinstall this back on without the car completely in the air on a lift, to allow enough angle for the exhaust to clear correctly.
-Don
If really needed, I can have it welded back on. However, the bolts are rusted to the section that I cut off from the mid pipes. I also do not know/see how it'd even be possible to reinstall this back on without the car completely in the air on a lift, to allow enough angle for the exhaust to clear correctly.
-Don
#13
TECH Apprentice
Thread Starter
iTrader: (2)
Join Date: Aug 2008
Location: Irvine, CA
Posts: 344
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Pictures of the exhaust.
![](http://www.wannaberacer.com/misc/camaro6.jpg)
![](http://www.wannaberacer.com/misc/camaro7.jpg)
Both exhaust tips got a bit of damage on them, from when the car was coming on/off of the tow truck.
![](http://www.wannaberacer.com/misc/camaro8.jpg)
Picture of the mid pipes, in case anyone wanted to see.
![](http://www.wannaberacer.com/misc/camaro9.jpg)
-Don
![](http://www.wannaberacer.com/misc/camaro6.jpg)
![](http://www.wannaberacer.com/misc/camaro7.jpg)
Both exhaust tips got a bit of damage on them, from when the car was coming on/off of the tow truck.
![](http://www.wannaberacer.com/misc/camaro8.jpg)
Picture of the mid pipes, in case anyone wanted to see.
![](http://www.wannaberacer.com/misc/camaro9.jpg)
-Don