Stock 2003 Z06 (with 19's and 20's) vs 383 F-Body and Stalled F-Body
#41
Banned
iTrader: (1)
Join Date: Jan 2007
Location: Okinawa, Japan/Fort Worth, TX
Posts: 386
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
^Yeah but what about those pullied Cobras that only trap 116-118 and those C5Z06s that trap 118-120? Its not probable but very possible, Ive seen pullied Cobras get beat by stock Zs on many occasions. But then again Ive watched pullied Cobras take down cammed and full bolt-on Z06s, its not a black and white subject.
#42
Administrator
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
^Yeah but what about those pullied Cobras that only trap 116-118 and those C5Z06s that trap 118-120? Its not probable but very possible, Ive seen pullied Cobras get beat by stock Zs on many occasions. But then again Ive watched pullied Cobras take down cammed and full bolt-on Z06s, its not a black and white subject.
more so than from a roll where it's all about ET. I was trapping 120-121mph
with the pulley. I never had any problems at all with stock Z06's...even
from a roll.
#43
Banned
iTrader: (1)
Join Date: Jan 2007
Location: Okinawa, Japan/Fort Worth, TX
Posts: 386
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
^Ehh, I guess we have to say "anything can happen on the street". I hate using that but its true, if you try to make it a clear cut thing then you will get confused because there are multiple vids to back up either argument. Id like to say power to weight is all that matters but that s/c lowe end can make up for that and on the highway sometimes even trap speeds dont tell the whole story.
#45
Administrator
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I have to agree with that too. That's twice in the same thread! ![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
^Ehh, I guess we have to say "anything can happen on the street". I hate using that but its true, if you try to make it a clear cut thing then you will get confused because there are multiple vids to back up either argument. Id like to say power to weight is all that matters but that s/c lowe end can make up for that and on the highway sometimes even trap speeds dont tell the whole story.
#46
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
^Yeah but what about those pullied Cobras that only trap 116-118 and those C5Z06s that trap 118-120? Its not probable but very possible, Ive seen pullied Cobras get beat by stock Zs on many occasions. But then again Ive watched pullied Cobras take down cammed and full bolt-on Z06s, its not a black and white subject.
#47
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Isn't this your car? And I'm well aware of what c5 z's are capable of.
http://videos.streetfire.net/video/r...bra_166327.htm
http://videos.streetfire.net/video/r...bra_166327.htm
![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
I have no clue what my main point is
![Icon Confused](https://ls1tech.com/forums/images/smilies2/icon_confused.gif)
#48
TECH Addict
iTrader: (12)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Yes sir that was, quite awhile back as well when i was greenhorn.
Its pretty well said i damn good driver in any 6spd car can do some damage. Im not the best but im no slouch either, but some cars tend to run harder than others, what some would call freaks. A pullied cobra ported or not should always pull harder up top same as i expected for the 383 car. Then again if you dont research your build on your motor properly or have a good tune all your cubic inchs, your big cam, or ported heads arent worth a damn. Its harder to build bad *** n/a motor than it is build a full bolt on cobra.
I have no clue what my main point is
Just thought id throw my scrambled two cents.
![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
I have no clue what my main point is
![Icon Confused](https://ls1tech.com/forums/images/smilies2/icon_confused.gif)