Capn Smokey & The 200 MPH 3rd Gen
#102
Banned
iTrader: (1)
Join Date: Jan 2007
Location: Okinawa, Japan/Fort Worth, TX
Posts: 386
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Marc 85Z28
Hahahahaha! The ZZ4 was rated at 355HP, and per GM, in 3rd gen trim (as per the ZZ4 conversion) was only capable of 308HP. That's rated at the engine, not the wheels.
Secondly, I've built several SBCs, and while I haven't built your specific combo, I know enough to say that you have a 400HP engine there - and I'm not talking wheel HP! A relatively low compression, 180cc runner, 230 duration cam just isn't going to make impressive power.
I think if you actually put that car on a dyno or ran it on a quarter mile, you'd think differently about its power output. I really hate to do this, but you're claiming 100-120 more rwhp over a stock ZZ4 (that's roughly 150 more engine HP) with heads that flow 30cfm more and a cam 10 degrees bigger!?
Finally, I'd say you're 400-420rwhp estimate is a pretty decent one, WITH THE SPRAY.
Secondly, I've built several SBCs, and while I haven't built your specific combo, I know enough to say that you have a 400HP engine there - and I'm not talking wheel HP! A relatively low compression, 180cc runner, 230 duration cam just isn't going to make impressive power.
I think if you actually put that car on a dyno or ran it on a quarter mile, you'd think differently about its power output. I really hate to do this, but you're claiming 100-120 more rwhp over a stock ZZ4 (that's roughly 150 more engine HP) with heads that flow 30cfm more and a cam 10 degrees bigger!?
Finally, I'd say you're 400-420rwhp estimate is a pretty decent one, WITH THE SPRAY.
I think you may wanna reconsider your statment, my heads have minor port work done and IIRC they flowed around 295cfm and I have 10:1 cr. The cam in my sig is an old one, I need to update it but the new one is a 238/242 .576/.582 on a 108lsa. I have a proform race carb sitting on a port matched victor jr. with an msd pro billet distributor and scorpion roller rockers so wtf makes you think I only make 400fwhp? If you wanna argue this then you are an idiot, my car weighs 3400lb with me in it so from my gathering it should be at about 400whp. The one and only time I went to the track it trapped 93mph on motor in the 1/8, I wish I wouldnt have thrown the timeslip away(I was embarrassed of my 2.1 60').
#105
Teching In
Join Date: Apr 2007
Location: Orange County California
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by capn smokey
The one and only time I went to the track it trapped 93mph on motor in the 1/8, I wish I wouldnt have thrown the timeslip away(I was embarrassed of my 2.1 60').
#107
Administrator
Originally Posted by Pharm0r
although im skeptical on weather or not smoky can go as fast as he claims i have noticed two things.
cj, you are a tool for starting a flame war for no reason other than your personal amusment. Smoky is full of **** and everyone thinks so. Get the **** over it already.
Unit, the fact that you let this thread live is a tarnish on you as a mod. In my opinion you (kepping in mind that you are in fact a mod) should go back and read the rules for this section. So far in the first 3 pages the following rules were broken: 1, 4, 6, 8, 9...
now, ill stress, this is just my opinion. i think you do a good job as a mod, but this thread is .
+1
cj, you are a tool for starting a flame war for no reason other than your personal amusment. Smoky is full of **** and everyone thinks so. Get the **** over it already.
Unit, the fact that you let this thread live is a tarnish on you as a mod. In my opinion you (kepping in mind that you are in fact a mod) should go back and read the rules for this section. So far in the first 3 pages the following rules were broken: 1, 4, 6, 8, 9...
now, ill stress, this is just my opinion. i think you do a good job as a mod, but this thread is .
+1
damn post...that is until they really need to be locked down.
...and tarnish my reputation? Puh-lease...I own a Cobra and I'm a mod
on a LSx site. There's not much left to tarnish. However, the
real members here know what I'm about.
Thanks for you input though.
#109
TECH Fanatic
iTrader: (8)
Originally Posted by capn smokey
Heres an article for you to read http://www.chevyhiperformance.com/te...e_engine_build
I think you may wanna reconsider your statment, my heads have minor port work done and IIRC they flowed around 295cfm and I have 10:1 cr. The cam in my sig is an old one, I need to update it but the new one is a 238/242 .576/.582 on a 108lsa. I have a proform race carb sitting on a port matched victor jr. with an msd pro billet distributor and scorpion roller rockers so wtf makes you think I only make 400fwhp? If you wanna argue this then you are an idiot, my car weighs 3400lb with me in it so from my gathering it should be at about 400whp. The one and only time I went to the track it trapped 93mph on motor in the 1/8, I wish I wouldnt have thrown the timeslip away(I was embarrassed of my 2.1 60').
I think you may wanna reconsider your statment, my heads have minor port work done and IIRC they flowed around 295cfm and I have 10:1 cr. The cam in my sig is an old one, I need to update it but the new one is a 238/242 .576/.582 on a 108lsa. I have a proform race carb sitting on a port matched victor jr. with an msd pro billet distributor and scorpion roller rockers so wtf makes you think I only make 400fwhp? If you wanna argue this then you are an idiot, my car weighs 3400lb with me in it so from my gathering it should be at about 400whp. The one and only time I went to the track it trapped 93mph on motor in the 1/8, I wish I wouldnt have thrown the timeslip away(I was embarrassed of my 2.1 60').
1. Your sig states you have 180cc intake runner cylinder heads. No 180 runner head, no matter what platform will flow 295cfm, at any lift. The only way your 180cc casting could be flowing 295cfm is if it were opened up to over 210cc (which is a TON), and then the 295cfm would only be at .7" lift or more - where your new fictional cam doesn't open that far.
2. Your sig states you have a 230 duration single pattern cam, not the 238/242 cam you claim you now have.
3. Nice article by Chevy High Performance. Too bad that not only does it back up my claim that an engine with the specs you list in your sig would make around 400HP, but the build they went with HAS NOTHING IN COMMON WITH YOUR MYTHICAL ENGINE!
The new combo you're talking about could make close to 400rwhp, but not through a shitty header like you've got... which begs the question... Any more changes you want to make to your new fictional engine?
Last edited by Marc 85Z28; 09-07-2007 at 08:24 PM.
#110
11 Second Club
iTrader: (88)
Originally Posted by Marc 85Z28
The new combo you're talking about could make close to 400rwhp, but not through a shitty header like you've got... which begs the question... Any more changes you want to make to your new fictional engine?
Anyone know what JATO Units are..
Next thing you know..he will have LT4 Heads on it..
Originally Posted by phrozen755
hey F**k you, I owned a kia once
A friend of mine, she had a Kia, always tried to race me everywhere..lol
#112
Kleeborp the Moderator™
iTrader: (11)
Originally Posted by capn smokey
The one and only time I went to the track it trapped 93mph on motor in the 1/8, I wish I wouldnt have thrown the timeslip away(I was embarrassed of my 2.1 60').
#113
Banned
iTrader: (1)
Join Date: Jan 2007
Location: Okinawa, Japan/Fort Worth, TX
Posts: 386
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Marc 85Z28
OK... here goes.
1. Your sig states you have 180cc intake runner cylinder heads. No 180 runner head, no matter what platform will flow 295cfm, at any lift. The only way your 180cc casting could be flowing 295cfm is if it were opened up to over 210cc (which is a TON), and then the 295cfm would only be at .7" lift or more - where your new fictional cam doesn't open that far.
2. Your sig states you have a 230 duration single pattern cam, not the 238/242 cam you claim you now have.
3. Nice article by Chevy High Performance. Too bad that not only does it back up my claim that an engine with the specs you list in your sig would make around 400HP, but the build they went with HAS NOTHING IN COMMON WITH YOUR MYTHICAL ENGINE!
The new combo you're talking about could make close to 400rwhp, but not through a shitty header like you've got... which begs the question... Any more changes you want to make to your new fictional engine?
1. Your sig states you have 180cc intake runner cylinder heads. No 180 runner head, no matter what platform will flow 295cfm, at any lift. The only way your 180cc casting could be flowing 295cfm is if it were opened up to over 210cc (which is a TON), and then the 295cfm would only be at .7" lift or more - where your new fictional cam doesn't open that far.
2. Your sig states you have a 230 duration single pattern cam, not the 238/242 cam you claim you now have.
3. Nice article by Chevy High Performance. Too bad that not only does it back up my claim that an engine with the specs you list in your sig would make around 400HP, but the build they went with HAS NOTHING IN COMMON WITH YOUR MYTHICAL ENGINE!
The new combo you're talking about could make close to 400rwhp, but not through a shitty header like you've got... which begs the question... Any more changes you want to make to your new fictional engine?
It appears they flow 270 out of the box, amazing aint it? And trapping 93 isnt hard in a car that weighs 3150lbs dry on a 60 degree night. Im not claiming to make outrageous power numbers but when cam-only LS1 cars can do 450-460whp why cant a properly built sbc do 400? Just cause I dont meticulously maintain my sig doesnt make me a liar, I have other **** to do besides sit around on the internet all day. And having mid-length headers doesnt make a whole lot of diferrence retard, I have seen tests with 5-10hp diferrence between Lts and shorties. You obviously dont know as much as you think.
#114
11 Second Club
iTrader: (19)
Originally Posted by unit213
...and tarnish my reputation? Puh-lease...I own a Cobra and I'm a mod
on a LSx site. There's not much left to tarnish. However, the
real members here know what I'm about.
Thanks for you input though.
#116
TECH Fanatic
iTrader: (8)
Originally Posted by capn smokey
It appears they flow 270 out of the box, amazing aint it?
Originally Posted by capn smokey
And having mid-length headers doesnt make a whole lot of diferrence retard, I have seen tests with 5-10hp diferrence between Lts and shorties. You obviously dont know as much as you think.
#117
BUILT FUCKEN RACE CARS CAN DO WHAT EVER THE **** YOU WANT!!!!!!
KEY FUCKEN WORD CUSTOM BUILT RACE CARS!
CUSTOM BUILT
CUSTOM BUILT
CUSTOM BUILT
CUTSTOM BUILT
CUSTOM BUILT
NOT STOCK
TURBO BUILT MOTORS
BUILT BUILT CARS
Damn everyone with there lack of reading
Originally Posted by brian06eleanor
he said his car is more aerodynamic than the c6zo6
KEY FUCKEN WORD CUSTOM BUILT RACE CARS!
CUSTOM BUILT
CUSTOM BUILT
CUSTOM BUILT
CUTSTOM BUILT
CUSTOM BUILT
NOT STOCK
TURBO BUILT MOTORS
BUILT BUILT CARS
Damn everyone with there lack of reading
Originally Posted by brian06eleanor
he said his car is more aerodynamic than the c6zo6