Post pics of your garage / shop
09-29-2009, 01:37 AM
#490
TECH Enthusiast
iTrader: (16)
Join Date: Jun 2004
Location: Farmingville, New York
Posts: 586
Likes: 0
Received 0 Likes
on
0 Posts
I've got to get a better shot, but I just went through all of the pages in this post and figured I'd post the picture I have now. I actually snapped this for another site, but here it is anyway! You can kinda see the lift with my '71 Camaro on it and my '68 Barracuda under it.
09-29-2009, 12:03 PM
#491
TECH Fanatic
iTrader: (6)
Join Date: Dec 2001
Location: LV NV
Posts: 1,114
Likes: 0
Received 0 Likes
on
0 Posts
I looked....not a single picture of hundreds of the garage. I guess Ill have to take some. I have my own dyno, but not for cars (sad) I have a bike dyno. I can dyno bikes, quads, and side by sides (rhinos, razors)
I ve looked into a cell dyno a couple times. No funds yet. Mine is 40x60 x 16 with a 20x40 second floor with storage and a studio apartment.
2 lifts, mandrel bender, tig, mig, gas, engine room, dirty room, etc...the usual, but by far the best addition was the water fountain. Chilled water....got rid of trash cans full of drink containers. Ive got two commercial swampers to put on now. Next summer should be real nice.
I ve looked into a cell dyno a couple times. No funds yet. Mine is 40x60 x 16 with a 20x40 second floor with storage and a studio apartment.
2 lifts, mandrel bender, tig, mig, gas, engine room, dirty room, etc...the usual, but by far the best addition was the water fountain. Chilled water....got rid of trash cans full of drink containers. Ive got two commercial swampers to put on now. Next summer should be real nice.
10-03-2009, 04:31 PM
#493
Staging Lane
Join Date: May 2008
Posts: 85
Likes: 0
Received 0 Likes
on
0 Posts
My workshop. Is in the old **** basement (where the pig sh**t usually goes) Took me 2 weeks of washing, then drying, painting, new concrete floor. ALOT of work 
Just moved in so im spending all my $$$ on new tools. Going slow with the turbo ls1 rx7!
Getting better everyday!
Just moved in so im spending all my $$$ on new tools. Going slow with the turbo ls1 rx7!
Getting better everyday!
10-03-2009, 05:54 PM
#495
Staging Lane
Join Date: May 2008
Posts: 85
Likes: 0
Received 0 Likes
on
0 Posts
Thanks! =)
The S14 is a killer. We dynoed it at 502rwhp on E85 with maxxed injectors. Turned the boost to 20psi and got 430rwhp and instant spool, and this with the SR20, forged internals and some other stuff. It eats the bad nissan transmissions so its getting a BMW M3 tranny this winter.
The silva sedan thing isnt that wild. Just a cheap but functional track/drift car.
Mine, the RX7 is getting a turbo`d LS1 engine. Played alot with rotaries but im ready for something new. Aiming for perfect weight distribution and enaugh power to have fun. Its hard to keep it a low budget car, but i try!
Just rough cutted firewall to get the engine where it should. I think its in a wrong angle at that picture, but the entire engine is behind the front axle =)
The S14 is a killer. We dynoed it at 502rwhp on E85 with maxxed injectors. Turned the boost to 20psi and got 430rwhp and instant spool, and this with the SR20, forged internals and some other stuff. It eats the bad nissan transmissions so its getting a BMW M3 tranny this winter.
The silva sedan thing isnt that wild. Just a cheap but functional track/drift car.
Mine, the RX7 is getting a turbo`d LS1 engine. Played alot with rotaries but im ready for something new. Aiming for perfect weight distribution and enaugh power to have fun. Its hard to keep it a low budget car, but i try!
Just rough cutted firewall to get the engine where it should. I think its in a wrong angle at that picture, but the entire engine is behind the front axle =)
