wheel sizing chart
wheel sizing chart new wheel chart.
The left side would be the inner wheel well.
the center line is the mounting surface.
Common sizes from the threads I've read,
and the 3 sets I've had.
zr1's, zo6's, fikses, hre's, stock ect.
If you see mistakes let me know.
scroll down for bigger chart
The left side would be the inner wheel well.
the center line is the mounting surface.
Common sizes from the threads I've read,
and the 3 sets I've had.
zr1's, zo6's, fikses, hre's, stock ect.
If you see mistakes let me know.
scroll down for bigger chart
Last edited by TTSSZ; Jul 27, 2005 at 09:38 PM.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Originally Posted by Hawkeye2
So, if I'm reading it correctly - eg. rear ZR1 - GS offset - 50mm. Rim width is
11", from mounting surface to the rear is 7 & 11/16ths, that would leave
3 & 5/16ths needed to clear the fender lip. Cest Correct?
11", from mounting surface to the rear is 7 & 11/16ths, that would leave
3 & 5/16ths needed to clear the fender lip. Cest Correct?
Ya, the rim lip width is a slight plus or minus number on most of them using the info I got from measuring the HRE’s. Some rims have a slightly bigger lip but those are close. I used the same lip width to calculate the backspaces that are shown.
The stock 9” SS rim was 9 ½” out to out - The 11” HRE was 11 7/16” out to out.
The stock 9” SS rim was 9 ½” out to out - The 11” HRE was 11 7/16” out to out.
Joined: Apr 2004
Posts: 1,378
Likes: 14
From: Atlanta, GA Ft. Walton Beach, FL
Ta
Originally Posted by FLAWLS1T/A
Amazing
Only If It Was Bigger
This Should Become A Sticky!!@!@!@!%$!!
Only If It Was Bigger
This Should Become A Sticky!!@!@!@!%$!!
? have you tinted you're windsheild?
Originally Posted by justfender6
will the c6 rims 18x9.5 w/ +59 offset fit the way all around?
It will have a 7 3/8" backspacing
so it will stick out 1/8" more then the stock rim and be 3/8" in more.
.....as far as I can tell.
I am wanting to send my factory rear 01/02 WS6 wheels off to be widened to 11" so I can run a 315/35/17 tire. Is it possible to do this without having to do the bfh mod or use a spacer? If so can you tell me what BS and offset I would need. I want the end result to look just like the factory set up but with a wider tire on it and I'm not sure if I have the graph figured out entirely. Any information is greatly appreciated.