Nitrous Related Wiring
Guest
Posts: n/a
Originally Posted by HAHA I 1
NX wet kit with Nitrous Outlet 4- switch panel, purge, Trick window switch with TPS sensor, FPSS, heater, opener
Can someone give me a hand with that one?
Can someone give me a hand with that one?
https://ls1tech.com/forums/showpost....9&postcount=85
https://ls1tech.com/forums/showpost....1&postcount=94
most combinations are posted at this point...if you compare the wiring diagram for the system to the one posted for the window switch there are only 2 wires that tap into the system wiring...the white goes to arming switch and the yellow goes to the ground side of the nitrous relay.
The FPSS goes inline on the yellow wire from the window switch
TransBrake & Nitrous (nitrous off/trans brake on) ???
I have a Nitro dave single stage plate kit already installed with purge, fpss, 860 heater, N O dig. window switch, WOT switch.
All Im adding is the t-brake.
thanks.
I have a Nitro dave single stage plate kit already installed with purge, fpss, 860 heater, N O dig. window switch, WOT switch.
All Im adding is the t-brake.
thanks.
Guest
Posts: n/a
Originally Posted by billybadd
TransBrake & Nitrous (nitrous off/trans brake on) ???
I have a Nitro dave single stage plate kit already installed with purge, fpss, 860 heater, N O dig. window switch, WOT switch.
All Im adding is the t-brake.
thanks.
I have a Nitro dave single stage plate kit already installed with purge, fpss, 860 heater, N O dig. window switch, WOT switch.
All Im adding is the t-brake.
thanks.
looks like that is one that was lost...so here it is again
Originally Posted by Ray@Nitrous Outlet
looks like that is one that was lost...so here it is again
Looking for the wiring diagram for a TPS switch. The switch I have came with a TNT wet kit and is about a year old. It is a black plastic box with no writing on it and no instructions. I understand how it works but I cant find the schematic for it. Here's a couple of pics, ignore the black electric tape residue all over the wires. BTW, the yellow wire was hooked up to "85" on my relay, if that helps.
Thanks for the help
Thanks for the help
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Ughh I wish that diagram of the dry kit with MSD WS and FPSS was still available. If anyone happens to have that one saved or something post it up or send it my way please.
Is this correct?
Guest
Posts: n/a
Looking for the wiring diagram for a TPS switch. The switch I have came with a TNT wet kit and is about a year old. It is a black plastic box with no writing on it and no instructions. I understand how it works but I cant find the schematic for it. Here's a couple of pics, ignore the black electric tape residue all over the wires. BTW, the yellow wire was hooked up to "85" on my relay, if that helps.
Thanks for the help
Thanks for the help
Guest
Posts: n/a
this is a few posts above yours...should get you close
https://ls1tech.com/forums/showpost....&postcount=137
https://ls1tech.com/forums/showpost....&postcount=137
just ordered my nitrous outlet tpas/window switch for my 99 vette, im sure the instructions are complete but im just doing some research before i install the kit. the tpas/ws sends ground to the relay for the noids. ill be using a fpss as well, i assume ill just send the ground output from the tpas/ws box to the fpss then back to the relay.
sound right ?
thanks
sound right ?
thanks
