going to the dark side *engine is in*
#401
It's always a fun time! I wouldn't say "never" i got my mother's 1970 LS-5 Chevelle SS to pull the drivers front up about 4 inches - stock.
#402
TECH Fanatic
Thread Starter
iTrader: (8)
Join Date: Sep 2007
Location: Hillsboro Kansas
Posts: 1,823
Likes: 0
Received 0 Likes
on
0 Posts
things are looking good for my project, the lt1 should be sold tomorrow, plus another $500 for selling front end loader... that will give me the money for heads, cam, and gaskets. i hope. then i can drop it in. and start with the wiring harness. merv you should tell me what wires i need to change/repin/add
#403
TECH Fanatic
Thread Starter
iTrader: (8)
Join Date: Sep 2007
Location: Hillsboro Kansas
Posts: 1,823
Likes: 0
Received 0 Likes
on
0 Posts
finally pulled the trigger, i called tsp and ordered a 3 bolt 229/236 112lsa cam. said it will ship tomorrow so by friday i hope to have my shortblock done.
im still looking for another 5364 casting head. then i need headers and tb, stall and bellhousing
im still looking for another 5364 casting head. then i need headers and tb, stall and bellhousing
#407
Where's a good place to seek out the LS1 T56 front plate?....I imagine a later year T5 front is not the same....is so please chime in.
Starting to look like it would have to be ordered stand alone from a rebuild shop. Anyone ever seen one otherwise?
An LS1 flywheel is also needed correct?...the LT1 will not do there as well.
Starting to look like it would have to be ordered stand alone from a rebuild shop. Anyone ever seen one otherwise?
An LS1 flywheel is also needed correct?...the LT1 will not do there as well.
#410
I would assume you'd need the curved one that was on the 5.3s with the 4L60Es. 6.0s used the flat ones with a 4L80E from the factory. IIRC the TBSS's use the curved ones with the 4L70E, so it should be the same for your application.
#411
TECH Fanatic
Thread Starter
iTrader: (8)
Join Date: Sep 2007
Location: Hillsboro Kansas
Posts: 1,823
Likes: 0
Received 0 Likes
on
0 Posts
alright, thanks. those are fairly cheap. the guy backed out on the lt1 and the loader guy has been too busy to come buy it. so im stuck with $67 dollars in my checking account till next week
#412
TECH Fanatic
Thread Starter
iTrader: (8)
Join Date: Sep 2007
Location: Hillsboro Kansas
Posts: 1,823
Likes: 0
Received 0 Likes
on
0 Posts
no real updates today/this week.
i painted the valve covers black the coil brackets, waterpump, a/c bracket, compressor, valley cover, and front cover an aluminum color by plastikote. it looks good imho but i wish i would have just cleaned them or had them powdercoated. also have a deal going on a pair of l92 heads so i should be getting close soon.
gonna try to sell the single head i have to fund the valve springs... but tsp wont tell me exactly which ones i need for my cam.
i painted the valve covers black the coil brackets, waterpump, a/c bracket, compressor, valley cover, and front cover an aluminum color by plastikote. it looks good imho but i wish i would have just cleaned them or had them powdercoated. also have a deal going on a pair of l92 heads so i should be getting close soon.
gonna try to sell the single head i have to fund the valve springs... but tsp wont tell me exactly which ones i need for my cam.
#414
TECH Fanatic
Thread Starter
iTrader: (8)
Join Date: Sep 2007
Location: Hillsboro Kansas
Posts: 1,823
Likes: 0
Received 0 Likes
on
0 Posts
Ok guys its been awhile, I lost interest in the project during deer season, but I'm back in the game!
I purchased all the engine bolts I need from another member on here and a pair of l92 heads. I will take pics when I get the heads and after they have been machined then I need to get lifters pushrods and valve springs. The engine will be sealed. And ready for me to finish the engine bay to drop it in.
I purchased all the engine bolts I need from another member on here and a pair of l92 heads. I will take pics when I get the heads and after they have been machined then I need to get lifters pushrods and valve springs. The engine will be sealed. And ready for me to finish the engine bay to drop it in.
#416
TECH Fanatic
Thread Starter
iTrader: (8)
Join Date: Sep 2007
Location: Hillsboro Kansas
Posts: 1,823
Likes: 0
Received 0 Likes
on
0 Posts
i ended up losing every pic i had on my phone since samsung sucks and kills themselves.
now i have an htc that takes great pics... right now its still on the engine stand in a trashbag
i will be ordering the head gaskets and sparkplugs and wires tomorrow... which plugs should i go with on my cammed l92 headed 6.0?
now i have an htc that takes great pics... right now its still on the engine stand in a trashbag
i will be ordering the head gaskets and sparkplugs and wires tomorrow... which plugs should i go with on my cammed l92 headed 6.0?
#418
TECH Fanatic
iTrader: (26)
Join Date: Mar 2010
Location: Milledgeville, GA
Posts: 1,909
Likes: 0
Received 0 Likes
on
0 Posts
I just looked and FULL list/retail price on them are: $49.72 (LS2) and $40.28 (LS3) each. That's not only at the dealership I work at, but GM's set list price for them. It sounds like someone is trying to rip you off.
#419
TECH Fanatic
Thread Starter
iTrader: (8)
Join Date: Sep 2007
Location: Hillsboro Kansas
Posts: 1,823
Likes: 0
Received 0 Likes
on
0 Posts
Yeah sdparts has them for 3x.xx
Valve covers are going to be redone with hydrographics along with the intake manifold. And a coil relocation i suppose to show off the topend.
Here's the big question now, how much can I have my l92 heads milled without having ptv clearance issues? The cam is 229/236 with .65x lift.
Valve covers are going to be redone with hydrographics along with the intake manifold. And a coil relocation i suppose to show off the topend.
Here's the big question now, how much can I have my l92 heads milled without having ptv clearance issues? The cam is 229/236 with .65x lift.
#420
TECH Fanatic
iTrader: (26)
Join Date: Mar 2010
Location: Milledgeville, GA
Posts: 1,909
Likes: 0
Received 0 Likes
on
0 Posts
Mine is .595" lift and 250*/266* on a 112* LSA. I am pretty much expecting ptv clearance issues with the flattop/no valve relief LS2 pistons and L92 heads. I'm planning on doing the "flycut for free" mod using a couple spare valves and stick on sand paper. There is a thread on here about it. I already bought drill stops for a few bucks at Harbor Freight. IF I turn out to have plenty of room, I'm considering running 1.8:1 exhaust rockers to help out the weaker exhaust ports of the L92's. Haven't checked into mixing aftermarket & stock rockers on LSx motors though.