Pat G spec cam results 226/230, Mike Norris tuning
#1
TECH Resident
Thread Starter
iTrader: (7)
Join Date: Jun 2006
Location: Fort Myers FL
Posts: 908
Likes: 0
Received 0 Likes
on
0 Posts
Pat G spec cam results 226/230, Mike Norris tuning
Finally got the car up to Mike Norris yesterday, and got it tuned. First off I'd like to thank Mike for all the **** he put up with tuning my car, apparently my car was falling flat on its face at about 4.5k and up, I took the plugs out, gapped them accordingly, and it got a little better. Well Mike pointed out it was something electrical, so I started checking grounds, and I found the drivers head grounds were loose . I tightened them up, Mike did some tuning, and this is what she put out.
Cam is from Patrick Guerra, 226/230 .598 .600 113+4
By fortmyerspolice
And to point out, my car is leaning out in the upper rpm's, Mike said I needed either a fuel pump or some injectors. But overall, I'm happy as a **** with this cam. I'll post up a video real soon.
Awesome job Patrick and Mike.
http://www.youtube.com/watch?v=zbMP6H3iAeQ
Here's the dyno vid
http://www.youtube.com/watch?v=ScLXqRg75VY
Cam is from Patrick Guerra, 226/230 .598 .600 113+4
By fortmyerspolice
And to point out, my car is leaning out in the upper rpm's, Mike said I needed either a fuel pump or some injectors. But overall, I'm happy as a **** with this cam. I'll post up a video real soon.
Awesome job Patrick and Mike.
http://www.youtube.com/watch?v=zbMP6H3iAeQ
Here's the dyno vid
http://www.youtube.com/watch?v=ScLXqRg75VY
Last edited by fortmyerspolice; 09-11-2009 at 06:06 PM.
#8
TECH Addict
iTrader: (11)
Very strong torque curve down low for just cam-only. I'm assuming you're running an LS6 intake? I'm very pleased with my Pat G cam. Mine's a little bit bigger (232/237) but now that we got rid of some knock, which I attribute to my catch can, we were able to add some timing and it responded very well! It was pretty easy to tune as well and almost drives like stock.
#10
TECH Resident
Thread Starter
iTrader: (7)
Join Date: Jun 2006
Location: Fort Myers FL
Posts: 908
Likes: 0
Received 0 Likes
on
0 Posts
No, there are EPS lobes from Engine Power Systems, basically they are easy on beehives and good for performance. PR's are 7.425, length wasn't verified, Mike Norris told me the preload was ok.
#11
TECH Regular
Join Date: Jan 2008
Location: Bellaire, TX
Posts: 458
Likes: 0
Received 0 Likes
on
0 Posts
i abot to install the same cam but with a 112+4 LSA
with stock 241 heads, LS6 intake, longtubes, and a 3200 stall with 3.73 gears.
i'll be running the cam with Comp 918 springs and 7.425 pushrods.
Would love to hear how it sounds????
with stock 241 heads, LS6 intake, longtubes, and a 3200 stall with 3.73 gears.
i'll be running the cam with Comp 918 springs and 7.425 pushrods.
Would love to hear how it sounds????
#12
LS1 Tech Administrator
iTrader: (14)
Those EPS lobes are quite a bit more spring-friendly than XFI or XE-R lobes even though the lift is similar. With a 7.425" pushrod and a quality beehive spring like a PAC 1518 or a Comp 26918, these lobes will allow very stable rpm stability in the upper 6000s. Nice detective work on finding the electrical gremlins. Many people would have laid blame on the cam and not investigated further. Thanks for sweating the details.
Dimitri's goal was to make over 400rwhp and have good street manners. Looks like both goals were met. Congrats!
Dimitri's goal was to make over 400rwhp and have good street manners. Looks like both goals were met. Congrats!
__________________
2013 Corvette Grand Sport A6 LME forged 416, Greg Good ported TFS 255 LS3 heads, 222/242 .629"/.604" 121LSA Pat G blower cam, ARH 1 7/8" headers, ESC Novi 1500 Supercharger w/8 rib direct drive conversion, 747rwhp/709rwtq on 93 octane, 801rwhp/735rwtq on race fuel, 10.1 @ 147.25mph 1/4 mile, 174.7mph Half Mile.
2016 Corvette Z51 M7 Magnuson Heartbeat 2300 supercharger, TSP LT headers, Pat G tuned, 667rwhp, 662rwtq, 191mph TX Mile.
2009.5 Pontiac G8 GT 6.0L, A6, AFR 230v2 heads. 506rwhp/442rwtq. 11.413 @ 121.29mph 1/4 mile, 168.7mph TX Mile
2000 Pewter Ram Air Trans Am M6 heads/cam 508 rwhp/445 rwtq SAE, 183.092 TX Mile
2022 Cadillac Escalade 6.2L A10 S&B CAI, Corsa catback.
2023 Corvette 3LT Z51 soon to be modified.
Custom LSX tuning in person or via email press here.
2013 Corvette Grand Sport A6 LME forged 416, Greg Good ported TFS 255 LS3 heads, 222/242 .629"/.604" 121LSA Pat G blower cam, ARH 1 7/8" headers, ESC Novi 1500 Supercharger w/8 rib direct drive conversion, 747rwhp/709rwtq on 93 octane, 801rwhp/735rwtq on race fuel, 10.1 @ 147.25mph 1/4 mile, 174.7mph Half Mile.
2016 Corvette Z51 M7 Magnuson Heartbeat 2300 supercharger, TSP LT headers, Pat G tuned, 667rwhp, 662rwtq, 191mph TX Mile.
2009.5 Pontiac G8 GT 6.0L, A6, AFR 230v2 heads. 506rwhp/442rwtq. 11.413 @ 121.29mph 1/4 mile, 168.7mph TX Mile
2000 Pewter Ram Air Trans Am M6 heads/cam 508 rwhp/445 rwtq SAE, 183.092 TX Mile
2022 Cadillac Escalade 6.2L A10 S&B CAI, Corsa catback.
2023 Corvette 3LT Z51 soon to be modified.
Custom LSX tuning in person or via email press here.
#17
#18
LS1 Tech Administrator
iTrader: (14)
With the EPS lobes couple with an engine running stock rockers, lifters and head gasket thickness, the 7.425" pushrods give pre-load closest to stock. This puts the pushrod in the middle of the plunger travel and makes for the most quiet operation. As you can see by the graph, the valvetrain stability is outstanding at high rpm.
__________________
2013 Corvette Grand Sport A6 LME forged 416, Greg Good ported TFS 255 LS3 heads, 222/242 .629"/.604" 121LSA Pat G blower cam, ARH 1 7/8" headers, ESC Novi 1500 Supercharger w/8 rib direct drive conversion, 747rwhp/709rwtq on 93 octane, 801rwhp/735rwtq on race fuel, 10.1 @ 147.25mph 1/4 mile, 174.7mph Half Mile.
2016 Corvette Z51 M7 Magnuson Heartbeat 2300 supercharger, TSP LT headers, Pat G tuned, 667rwhp, 662rwtq, 191mph TX Mile.
2009.5 Pontiac G8 GT 6.0L, A6, AFR 230v2 heads. 506rwhp/442rwtq. 11.413 @ 121.29mph 1/4 mile, 168.7mph TX Mile
2000 Pewter Ram Air Trans Am M6 heads/cam 508 rwhp/445 rwtq SAE, 183.092 TX Mile
2022 Cadillac Escalade 6.2L A10 S&B CAI, Corsa catback.
2023 Corvette 3LT Z51 soon to be modified.
Custom LSX tuning in person or via email press here.
2013 Corvette Grand Sport A6 LME forged 416, Greg Good ported TFS 255 LS3 heads, 222/242 .629"/.604" 121LSA Pat G blower cam, ARH 1 7/8" headers, ESC Novi 1500 Supercharger w/8 rib direct drive conversion, 747rwhp/709rwtq on 93 octane, 801rwhp/735rwtq on race fuel, 10.1 @ 147.25mph 1/4 mile, 174.7mph Half Mile.
2016 Corvette Z51 M7 Magnuson Heartbeat 2300 supercharger, TSP LT headers, Pat G tuned, 667rwhp, 662rwtq, 191mph TX Mile.
2009.5 Pontiac G8 GT 6.0L, A6, AFR 230v2 heads. 506rwhp/442rwtq. 11.413 @ 121.29mph 1/4 mile, 168.7mph TX Mile
2000 Pewter Ram Air Trans Am M6 heads/cam 508 rwhp/445 rwtq SAE, 183.092 TX Mile
2022 Cadillac Escalade 6.2L A10 S&B CAI, Corsa catback.
2023 Corvette 3LT Z51 soon to be modified.
Custom LSX tuning in person or via email press here.
#19
TECH Resident
Join Date: Sep 2003
Location: Working in the shop 24/7
Posts: 848
Likes: 0
Received 1 Like
on
1 Post
With the EPS lobes couple with an engine running stock rockers, lifters and head gasket thickness, the 7.425" pushrods give pre-load closest to stock. This puts the pushrod in the middle of the plunger travel and makes for the most quiet operation. As you can see by the graph, the valvetrain stability is outstanding at high rpm.
* just had to do it Pat *
#20
LS1 Tech Administrator
iTrader: (14)
It's OK Ed, I know where you're coming from. After playing around with PR lengths from 7.350-7.450" with these lobes, the 7.425" pushrods gave the best compromise in NVH and performance. These new lobes are some of Billy Godbold's favorites. They are a slightly calmer version of the new LSL lobe made specifically to be happy with beehive springs like the PAC 1518 and Comp 26918. The acceleration and jerk is much more friendly than XFI and XE-R lobes even though the duration at .006, .050, and .200" are similar. Of course, you know about all how subtle differences in ramp rate can make or break a good cam profile.
__________________
2013 Corvette Grand Sport A6 LME forged 416, Greg Good ported TFS 255 LS3 heads, 222/242 .629"/.604" 121LSA Pat G blower cam, ARH 1 7/8" headers, ESC Novi 1500 Supercharger w/8 rib direct drive conversion, 747rwhp/709rwtq on 93 octane, 801rwhp/735rwtq on race fuel, 10.1 @ 147.25mph 1/4 mile, 174.7mph Half Mile.
2016 Corvette Z51 M7 Magnuson Heartbeat 2300 supercharger, TSP LT headers, Pat G tuned, 667rwhp, 662rwtq, 191mph TX Mile.
2009.5 Pontiac G8 GT 6.0L, A6, AFR 230v2 heads. 506rwhp/442rwtq. 11.413 @ 121.29mph 1/4 mile, 168.7mph TX Mile
2000 Pewter Ram Air Trans Am M6 heads/cam 508 rwhp/445 rwtq SAE, 183.092 TX Mile
2022 Cadillac Escalade 6.2L A10 S&B CAI, Corsa catback.
2023 Corvette 3LT Z51 soon to be modified.
Custom LSX tuning in person or via email press here.
2013 Corvette Grand Sport A6 LME forged 416, Greg Good ported TFS 255 LS3 heads, 222/242 .629"/.604" 121LSA Pat G blower cam, ARH 1 7/8" headers, ESC Novi 1500 Supercharger w/8 rib direct drive conversion, 747rwhp/709rwtq on 93 octane, 801rwhp/735rwtq on race fuel, 10.1 @ 147.25mph 1/4 mile, 174.7mph Half Mile.
2016 Corvette Z51 M7 Magnuson Heartbeat 2300 supercharger, TSP LT headers, Pat G tuned, 667rwhp, 662rwtq, 191mph TX Mile.
2009.5 Pontiac G8 GT 6.0L, A6, AFR 230v2 heads. 506rwhp/442rwtq. 11.413 @ 121.29mph 1/4 mile, 168.7mph TX Mile
2000 Pewter Ram Air Trans Am M6 heads/cam 508 rwhp/445 rwtq SAE, 183.092 TX Mile
2022 Cadillac Escalade 6.2L A10 S&B CAI, Corsa catback.
2023 Corvette 3LT Z51 soon to be modified.
Custom LSX tuning in person or via email press here.