Big cam 346 power?
#1
TECH Apprentice
Thread Starter
Join Date: May 2005
Location: Huntsville, AL
Posts: 314
Likes: 0
Received 0 Likes
on
0 Posts
Big cam 346 power?
I am putting a huge cam in my 346. It is a 242/246 .621/.614 111LSA 109ICL.
The heads are 2.5 5.3 prc heads that are going to be milled .040. The SCR is going to be around 12.2:1 and the DCR will be 8.8:1. The bottom end will be completely freshened as well.
What type of power should this put down?
The heads are 2.5 5.3 prc heads that are going to be milled .040. The SCR is going to be around 12.2:1 and the DCR will be 8.8:1. The bottom end will be completely freshened as well.
What type of power should this put down?
#5
TECH Apprentice
Thread Starter
Join Date: May 2005
Location: Huntsville, AL
Posts: 314
Likes: 0
Received 0 Likes
on
0 Posts
less, like maybe 450. But, that is the way I think. Therefore, if it makes more than I was thinking, I will be very surprised! I like surprises!
Trending Topics
#10
10 Second Club
iTrader: (5)
Join Date: Jul 2005
Location: by my computer
Posts: 2,958
Likes: 0
Received 0 Likes
on
0 Posts
I am putting a huge cam in my 346. It is a 242/246 .621/.614 111LSA 109ICL.
The heads are 2.5 5.3 prc heads that are going to be milled .040. The SCR is going to be around 12.2:1 and the DCR will be 8.8:1. The bottom end will be completely freshened as well.
What type of power should this put down?
The heads are 2.5 5.3 prc heads that are going to be milled .040. The SCR is going to be around 12.2:1 and the DCR will be 8.8:1. The bottom end will be completely freshened as well.
What type of power should this put down?
MellowYellow has a RPM6.... 244/248 in a 346 with 10bolt and makes 440ish..... optimal setup with waterpump, pulley, and good exhaust thru a T56 might make 470ish.
#14
10 Second Club
iTrader: (17)
Join Date: Apr 2004
Location: Alloway,NJ
Posts: 2,409
Likes: 0
Received 0 Likes
on
0 Posts
try to get a fast 90/90 on there and if you have the money get it ported as well that should put you higher in the hp/tq range.....
depending on what you hit w/ the prc's i may be inclined to try them....rite now im infatuated w/ the tfs 215s and the afr 205s
when will you be done and on the dyno?
rite now id say around 460ish
-brandon
depending on what you hit w/ the prc's i may be inclined to try them....rite now im infatuated w/ the tfs 215s and the afr 205s
when will you be done and on the dyno?
rite now id say around 460ish
-brandon
#18
TECH Apprentice
Thread Starter
Join Date: May 2005
Location: Huntsville, AL
Posts: 314
Likes: 0
Received 0 Likes
on
0 Posts
#19
TECH Apprentice
Thread Starter
Join Date: May 2005
Location: Huntsville, AL
Posts: 314
Likes: 0
Received 0 Likes
on
0 Posts
try to get a fast 90/90 on there and if you have the money get it ported as well that should put you higher in the hp/tq range.....
depending on what you hit w/ the prc's i may be inclined to try them....rite now im infatuated w/ the tfs 215s and the afr 205s
when will you be done and on the dyno?
rite now id say around 460ish
-brandon
depending on what you hit w/ the prc's i may be inclined to try them....rite now im infatuated w/ the tfs 215s and the afr 205s
when will you be done and on the dyno?
rite now id say around 460ish
-brandon