Rear exit True Duals???
12-21-2008, 08:24 PM
#1
On The Tree
Thread Starter
iTrader: (2)
Join Date: Jun 2007
Location: Altamonte Springs, FL
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
Rear exit True Duals??? Ok, I've been searching on here for over an hour, and I can't get a straight answer on my question. 
Does ANYONE make an over the axle true dual set-up for LT1 cars? I want to have TD's put on the car, but I don't want to dump it under the car. I'd also perfer to have the mufflers mounted behind the axle. Some please have some good news for me. Thanks!
Does ANYONE make an over the axle true dual set-up for LT1 cars? I want to have TD's put on the car, but I don't want to dump it under the car. I'd also perfer to have the mufflers mounted behind the axle. Some please have some good news for me. Thanks! 
12-22-2008, 05:18 AM
#3
11 Second Club
iTrader: (13)
Join Date: Oct 2003
Location: apoopka, fl
Posts: 1,414
Likes: 0
Received 0 Likes
on
0 Posts
theres a guy in melbourne who had 3" true duals over the axel on his 94 Z28 it was a bad *** set up.. but i'm sure it wasn't cheap..
give him a call 321-863-4792 i'm sure he could do it again.. his names rick
give him a call 321-863-4792 i'm sure he could do it again.. his names rick
12-22-2008, 08:52 AM
#5
Someone had just done this in the LT1 section about a month ago, had pictures too. I've been having a hard time finding the thread though, cause when I can afford to I want to copy it. I've got dumped duals after a Hpipe, but have the SLP subframe connectors, so my exhaust hangs stupid low to clear them.
12-22-2008, 10:14 AM
#6
TECH Resident
iTrader: (35)
Join Date: Nov 2007
Location: Rowlett, TX
Posts: 762
Likes: 0
Received 0 Likes
on
0 Posts
I would talk to Mr Muffler in Sanford. His name is Jamie.
I was referred there by a fellow member and have referred others there as well for exhaust work. He knows the F-Bodys, and will do a custom job on your set-up. His work is nice and clean, no short-cuts or crappy welds, nice clean bends too. He could probably do what you are asking of.
Drop me a PM since he is not a sponsor on here. I will give you his phone number up there.
Steve
I was referred there by a fellow member and have referred others there as well for exhaust work. He knows the F-Bodys, and will do a custom job on your set-up. His work is nice and clean, no short-cuts or crappy welds, nice clean bends too. He could probably do what you are asking of.
Drop me a PM since he is not a sponsor on here. I will give you his phone number up there.
Steve
12-22-2008, 11:58 AM
#7
I would talk to Mr Muffler in Sanford. His name is Jamie.
I was referred there by a fellow member and have referred others there as well for exhaust work. He knows the F-Bodys, and will do a custom job on your set-up. His work is nice and clean, no short-cuts or crappy welds, nice clean bends too. He could probably do what you are asking of.
Drop me a PM since he is not a sponsor on here. I will give you his phone number up there.
Steve
I was referred there by a fellow member and have referred others there as well for exhaust work. He knows the F-Bodys, and will do a custom job on your set-up. His work is nice and clean, no short-cuts or crappy welds, nice clean bends too. He could probably do what you are asking of.
Drop me a PM since he is not a sponsor on here. I will give you his phone number up there.
Steve
Trending Topics
12-22-2008, 10:02 PM
#8
On The Tree
Thread Starter
iTrader: (2)
Join Date: Jun 2007
Location: Altamonte Springs, FL
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
I would talk to Mr Muffler in Sanford. His name is Jamie.
I was referred there by a fellow member and have referred others there as well for exhaust work. He knows the F-Bodys, and will do a custom job on your set-up. His work is nice and clean, no short-cuts or crappy welds, nice clean bends too. He could probably do what you are asking of.
Drop me a PM since he is not a sponsor on here. I will give you his phone number up there.
Steve
I was referred there by a fellow member and have referred others there as well for exhaust work. He knows the F-Bodys, and will do a custom job on your set-up. His work is nice and clean, no short-cuts or crappy welds, nice clean bends too. He could probably do what you are asking of.
Drop me a PM since he is not a sponsor on here. I will give you his phone number up there.
Steve
12-23-2008, 11:58 PM
#10
On The Tree
Thread Starter
iTrader: (2)
Join Date: Jun 2007
Location: Altamonte Springs, FL
Posts: 156
Likes: 0
Received 0 Likes
on
0 Posts
