Breaking in FI motor
#4
On The Tree
iTrader: (4)
Join Date: Apr 2009
Location: Springfield, Illinois
Posts: 167
Likes: 0
Received 0 Likes
on
0 Posts
according to the majority on here the consensus is to vary the rpms and lots of engine breaking. Just make sure you get into it hard because the rings break in very quickly and it is imparitive you do this within the first 100-250 miles. If someone disagrees that is there opinion, I also was under the assumption you "baby it" for some many hundred miles before you go wot but many say thats the opposite of what you want to do. I have also done lots of searching and everyones opinion will vary on this topic but again this is the consensus of many people saying get into it decently hard in the beginning vs babying the car.
#9
TECH Addict
iTrader: (8)
What is there to break in? Rings break in instantly... Take that thing out and put it to the floor. Engines dont travel miles so thats meaningless.
I thought only ricers "break" stuff in. Seems to be the excuse they all have why they run their mouths and then cant race... lol.
I thought only ricers "break" stuff in. Seems to be the excuse they all have why they run their mouths and then cant race... lol.
#11
TECH Apprentice
I'd let it warm up and take it easy for the first few miles. But as said, rings seat almost instantly as long as everything is done correctly, throw the blower on and beat on it.
#12
10 Second Club
iTrader: (22)
Join Date: Mar 2006
Location: Northwest side of Chicago
Posts: 3,677
Likes: 0
Received 2 Likes
on
2 Posts
I agree. I let it go through a couple full heat cycles in the first day. Let it get hot,let it cool all the way down. Then its on. I mainly do that for the valve springs.
Probably doesn't make to much of a differance but why not.
Probably doesn't make to much of a differance but why not.
#14
11 Second Club
iTrader: (5)
This is one the automotive worlds greatest debates lol. I agree with what most the others have said and its what I did but once again, its a personal choice. I started my motor...let it idle for about 30 seconds to make sure there were no leaks or major issues and then slowly ran it from about 2K up to 4K and back down varrying rpm. Rings seat quickly under pressure so its important you don't let it idle for to long. I drove it up to my tuner the next am, got it tuned and ran his new 5.0 while my car was still N/A lol. It put down 370rwhp lol I try and change the oil after 100 and then 500 miles to make sure most of the metal particles have been removed. I also used Joe Gibbs break in oil with ZDDP.
Edit: I ran it without the blower but only because I was still waiting on parts. I would have ran it with if I had what I needed.
Edit: I ran it without the blower but only because I was still waiting on parts. I would have ran it with if I had what I needed.
#16
LS1Tech Sponsor
iTrader: (10)
Th most important thing for break in is having a proper tune up. If you are nailing the tune up fast then you should be ruining it just how you want to all the time.
Best thing is to start it up get oil and coolant up to temp and start making pulls with a good tune up, while monitoring everything in a closed environment. Preferably on the engine dyno or on the chassis dyno if the engine dyno is not a choice.
Best thing is to start it up get oil and coolant up to temp and start making pulls with a good tune up, while monitoring everything in a closed environment. Preferably on the engine dyno or on the chassis dyno if the engine dyno is not a choice.
#19
Th most important thing for break in is having a proper tune up. If you are nailing the tune up fast then you should be ruining it just how you want to all the time.
Best thing is to start it up get oil and coolant up to temp and start making pulls with a good tune up, while monitoring everything in a closed environment. Preferably on the engine dyno or on the chassis dyno if the engine dyno is not a choice.
Best thing is to start it up get oil and coolant up to temp and start making pulls with a good tune up, while monitoring everything in a closed environment. Preferably on the engine dyno or on the chassis dyno if the engine dyno is not a choice.