WS6 S475 official build thread.......
Thread Starter
TECH Fanatic
Joined: Mar 2011
Posts: 1,916
Likes: 8
From: Statesville, NC
Picked up these from a friend. Tires are nearly new. Gave him $250 and my factory wheels. I couldn't pass the deal up.
17s in front and 15x10s in the rear. Rear tires are 28-9.00 M/T. Fronts are M&H.
Had to barely sand the rear caliper and had to cut my bump stop bracket off the inside.
Few pictures. Ill take some later today outside where I can get the whole car.
17s in front and 15x10s in the rear. Rear tires are 28-9.00 M/T. Fronts are M&H.
Had to barely sand the rear caliper and had to cut my bump stop bracket off the inside.
Few pictures. Ill take some later today outside where I can get the whole car.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo Thread Starter
TECH Fanatic
Joined: Mar 2011
Posts: 1,916
Likes: 8
From: Statesville, NC
Get ready for a contortionist act when installing that cage, lol. It definitely taught me that welding on the bench is much different than in the car while upside down with one leg drapped over the rear seat while holding the torch in your off hand just to get the necessary angle, haha.
Thread Starter
TECH Fanatic
Joined: Mar 2011
Posts: 1,916
Likes: 8
From: Statesville, NC
Get ready for a contortionist act when installing that cage, lol. It definitely taught me that welding on the bench is much different than in the car while upside down with one leg drapped over the rear seat while holding the torch in your off hand just to get the necessary angle, haha.
Thread Starter
TECH Fanatic
Joined: Mar 2011
Posts: 1,916
Likes: 8
From: Statesville, NC
Thread Starter
TECH Fanatic
Joined: Mar 2011
Posts: 1,916
Likes: 8
From: Statesville, NC
New wheel and tire setup
I know its not LS related but we got this car in the shop over the weekend. Pretty rare and very clean. Doing a custom stainless exhaust system on it.
I know its not LS related but we got this car in the shop over the weekend. Pretty rare and very clean. Doing a custom stainless exhaust system on it.
Last edited by mrstepheneades; Dec 23, 2013 at 09:51 AM.
Thread Starter
TECH Fanatic
Joined: Mar 2011
Posts: 1,916
Likes: 8
From: Statesville, NC
Ive not seen but one other one on the highway in my life. Guess in my area they would be a rare car to see out.
And thanks on the compliment. I need a rear and a better torque arm setup. And a good driveshaft.
And thanks on the compliment. I need a rear and a better torque arm setup. And a good driveshaft.
You got a smoking deal on those wheels!!! Now try not to grenade that 10 bolt. My advice would be to go to your nearest Catholic church, bottle up some Holy Water and proceed to pour that **** all over that 10 bolt. 
Thread Starter
TECH Fanatic
Joined: Mar 2011
Posts: 1,916
Likes: 8
From: Statesville, NC
Your crazy lol. May try some 3000rpm launches off the 2step and see what it does. Keep the pressure up in the tires.
