Interesting intake
Thread Starter
9 Second Club
Joined: Nov 2003
Posts: 13,616
Likes: 185
From: Norn Iron
Interesting intake This popped up over on the Gen5 forum.
Looks like it could cover a wide range of fitments, similar design to some CNC'd stuff, but as this is a cast piece a much more friendly price.
http://www.camaro5.com/forums/showthread.php?p=9729226
Looks like it could cover a wide range of fitments, similar design to some CNC'd stuff, but as this is a cast piece a much more friendly price.
http://www.camaro5.com/forums/showthread.php?p=9729226
Teching In
Joined: Oct 2006
Posts: 34
Likes: 0
From: Richmond Va
I seen it in person at LS Fest West a few weeks ago. Good looking piece for sure. I didn't get much info on it but the car that it was on I believe was one of the designers/builders of the intake.
Thread Starter
9 Second Club
Joined: Nov 2003
Posts: 13,616
Likes: 185
From: Norn Iron
Some more info here
https://ls1tech.com/forums/generatio...ake-6-2-a.html
Which also links to here lol. Some graphs in this thread though and if legit do seem fairly impressive.
http://www.camaro5.com/forums/showthread.php?t=495133
https://ls1tech.com/forums/generatio...ake-6-2-a.html
Which also links to here lol. Some graphs in this thread though and if legit do seem fairly impressive.
http://www.camaro5.com/forums/showthread.php?t=495133
The fact that it looks like it made more torque than the stock intake above 4000 is very optimistic as most sheet metal intakes don't outperform till in the mid 5000 range.
I know I don't need anymore power or torque below 4000rpm, and if I do, I'll downshift, haha.
Considering at 4000rpm, my tires starting spinning on the dyno at 700ft/lbs of torque, losing 10-15 won't be missed.
I know I don't need anymore power or torque below 4000rpm, and if I do, I'll downshift, haha.
Considering at 4000rpm, my tires starting spinning on the dyno at 700ft/lbs of torque, losing 10-15 won't be missed.
Last edited by The Alchemist; May 19, 2017 at 07:31 AM.
Thread Starter
9 Second Club
Joined: Nov 2003
Posts: 13,616
Likes: 185
From: Norn Iron
Although it does have a good size plenum, more so than a lot of similar intakes. But it would still be more of a high rpm unit
And it looks good.
Trending Topics
It has a lot of things working for it. It looks good, it seems to be well constructed (guessing from the appearance), the dyno numbers on a stock ls3 from 4000 up seem to be promising, and the price is just slightly higher than the current composites from MSD and FAST.
Like I said, if it gives up a little below 4000rpm, I'm not overly concerned, but making more power at 4500 vs the typical 5000-6000 when sheetmetal intakes usually shine, that's huge because a lot of people hit that 4500rpm-5500rpm window on shifts.
Like I said, if it gives up a little below 4000rpm, I'm not overly concerned, but making more power at 4500 vs the typical 5000-6000 when sheetmetal intakes usually shine, that's huge because a lot of people hit that 4500rpm-5500rpm window on shifts.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
TECH Regular
Joined: Sep 2014
Posts: 433
Likes: 0
Looks kinda like a belt driven intake manifold... without the belt and pulley.
Sanitary look. I like it too. Out of the budget for anything I'm interested in doing. But certainly not out of the question for the guys playing with more than SBE stuff.
I'll be curious to see what the next year or so of results it produces.
Sanitary look. I like it too. Out of the budget for anything I'm interested in doing. But certainly not out of the question for the guys playing with more than SBE stuff.
I'll be curious to see what the next year or so of results it produces.
Thread Starter
9 Second Club
Joined: Nov 2003
Posts: 13,616
Likes: 185
From: Norn Iron
No doubt the usual, not a paying sponsor, so here's the webpage anyway
https://lodspeedworks.com/
Hopefully they will get it into production, unlike others that pop up, float about for years then never make it.
https://lodspeedworks.com/
Hopefully they will get it into production, unlike others that pop up, float about for years then never make it.
I have a decision to make... should I keep my MAST cathedral heads, or should I go with a rectangle port set of heads that allows me a wider option of intakes? Who knows.
Thread Starter
9 Second Club
Joined: Nov 2003
Posts: 13,616
Likes: 185
From: Norn Iron
There are a small few tests online with cathedral vs square...and even though the square ports claim much higher flow numbers, on the dyno there is negligible difference.
Is it worth changing heads though ? I just cant see it.
I've been using the same TFS225cc heads since 2008. If I want more power....just add more boost, bigger turbos etc. I dont believe my heads are a major limiting factor, certainly not enough to justify the cost to change.
I too met these folks at LS Fest West. Another great feature of the intake is that it is cast, so it should be at a much more affordable price point than the billet CNC units available.
edit nevermind I thought this was going to be for cathedrals aswell.
