Boost new guy map sensor question
Thread Starter
TECH Apprentice
Joined: Oct 2015
Posts: 310
Likes: 24
Boost new guy map sensor question How do you confirm or test your map sensor is set up correctly? I purchased the cobalt 2 bar sensor for an lsa swap. Gm # 12615136.
I am running a terminator x max and set the scale to the Holley 2 bar. Car is using 450lbs per hour and it says 7 psi at 6400 rpm.
just wondering if there was a way to confirm map sensor calibration.
I am running a terminator x max and set the scale to the Holley 2 bar. Car is using 450lbs per hour and it says 7 psi at 6400 rpm.
just wondering if there was a way to confirm map sensor calibration.
There is a version of a MightyVac that does both vacuum and pressure goes up to 30 psi and has an accurate gauge.
Key on, engine off, you can put 15 psi on the sensor and check what the Holley data says.
Its a handy tool for checking boost referenced fuel pressure regulators, waste gates and BOV’s as well.
Another test is to see what it reads key on engine off and the sensor open to air. Should read approx 100 kpa (14.7psi) plus or minus depending on your elevation.
Ron
Key on, engine off, you can put 15 psi on the sensor and check what the Holley data says.
Its a handy tool for checking boost referenced fuel pressure regulators, waste gates and BOV’s as well.
Another test is to see what it reads key on engine off and the sensor open to air. Should read approx 100 kpa (14.7psi) plus or minus depending on your elevation.
Ron
Maybe try setting up a Custom 2 bar MAP sensor and manually inputing the calibration curve. I'm not sure of exact values but it's going to be somewhere in the neighborhood of,
0V = 8 kPA
5V = 200 kPA
Baro and MAP pressure readings should be on top of each other with key on (before start up). If not, then your MAP calibration isn't passing the laugh test.
0V = 8 kPA
5V = 200 kPA
Baro and MAP pressure readings should be on top of each other with key on (before start up). If not, then your MAP calibration isn't passing the laugh test.
Trending Topics
Also, you can download HP Tuner for free and it will probably show the sensor calibration if you can find a stock file to download from a vehicle that used that sensor. That's the way I have unlocked a few mysteries.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
9 Second Club
Joined: Nov 2003
Posts: 13,616
Likes: 185
From: Norn Iron
Maybe try setting up a Custom 2 bar MAP sensor and manually inputing the calibration curve. I'm not sure of exact values but it's going to be somewhere in the neighborhood of,
0V = 8 kPA
5V = 200 kPA
Baro and MAP pressure readings should be on top of each other with key on (before start up). If not, then your MAP calibration isn't passing the laugh test.
0V = 8 kPA
5V = 200 kPA
Baro and MAP pressure readings should be on top of each other with key on (before start up). If not, then your MAP calibration isn't passing the laugh test.
Many operate linear in the 0.5 to 4.5v range
But testing is so easy, it is the safest option. Calibrate things correctly, not by guessing.
TECH Fanatic
Joined: Nov 2014
Posts: 1,308
Likes: 660
