mbm88

I actually really like the way dumps look...

From under the car.

RedLT4Mike

iTrader: (4)

I had em' like that and amazingly they worked great.
I've got dumped duals now, but would do under the axle
again if needed with no hesitation.

orangeapeel

iTrader: (18)

Always looked fine to me. it is cheaper money wise, not necessarily quality by any means. just a different route.

ws.6kid

because you lose the ability to use a lift when you go under the axle, since the rear end drops when you put the car on a lift. I think under the axle is ghetto no matter how clean it looks, there are no real advantages. BMR offers a Upper Panhard Rod Relocation Kit, which allows you to run 3" True Duals over the axle easily with no clearance issues.

Twotonefreak

iTrader: (11)

With the true duals I am still able to use a two post lift without the axle hitting the exhaust. I love the way mine sounds and plus a T/A doesn't look right w/out tips.

96lt1m6

iTrader: (31)

as far as the pipes "bottoming out" onto the rearend housing,it does not happen!
it works on both kinds of lifts,2 or 4 post.
corvettes have been this way for as a long time!
my ex.system has flanges built in so if i need to pull the rearend or do a fuel pump it is only 4 extra nuts to remove and my system comes down from the rear of the X-pipe back.
doing the over the axle 2.5 or 3" duals will not come out near as easy as mine
but reality time,how many times do you really need to access these items its not like an oil change or getting gas.
this mod is similar to all other mods, some like it... some dont..
like any other mod you do to your carjust make it as clean as possible!
everywhere i go someone comments about the sound then they actually get down to see the system and become even more impressed.

lilbuddy1587

iTrader: (1)

Ever hear about people bitching and complaining that their over the axle hits and clunks? Who says you lose the ability to use a lift with under the axle duals? Some people use flanges right at the muffler/axle so that they can take the tails off OR some people like myself just dont have a problem with it period. Then you have those that just can't justify/afford spending over a thousand dollars for an exhaust system. So that leaves you with the choice of under the axle duals OR a catback system with a big, ugly ******* muffler hanging in the back like a big diaper.

So tell me, which one is more "ghetto"

Clean look from behind, under the axle


or
A nice big shiny, diaper sticking out of the back with some tips?

speed_demon24

iTrader: (6)

at all the "experts" in here. I have mine under the axle and haven't scraped/bottomed them out yet. I can jack my car up and let the axle hang without any problems, and if I need to drop them for whatever reason (the only time I had to do this was to change my rear springs/shocks and it took a whiping 6 bolts to drop them) the exhaust pipes are already cool by the time I jack the car up and get my tools. I guess you do exhaust work when your engine is running?

99Hawk262

iTrader: (19)

It's hardly ghetto. I've never scraped at all. I have better clearance than I did with factory exhaust. Like I said, it takes a maximum of five minutes to drop them if I need to lift the car. Bottom line is, I didn't want to spend the extra $200 the shop wanted to run them over the axle. I also didn't want the headache of all the clanking and banging due to clearance issues. Granted a lot of cars don't have those problems, but I've seen enough that I didn't want to take any chances. I like them just fine....it's all personal preference. My duals are just as effective, look just as clean, and cost substantially less. Based on that, Why Not??

98Camarod

iTrader: (43)

I have dumps now and I am trying to get someone to finish them off out the back under the axle. It's not looking too promising in this neck of the woods. I had plans to have flanges on them. That way all you have to do is jack it up by the axle and unbolt them to throw it on a lift. That is truly the only downside to running them under the axle.

I'll glady spend ten minutes to unbolt them rather than spending the extra 600 bucks for the over the axle setup. Plus, its only 2.5" over the axle, not 3". On a side note, how the hell do you guys with dumps drive on the street with a cam and a stall. My car is crazy loud....

speed_demon24

iTrader: (6)

I have no problem with mine jacking the car up and letting the axle hang or putting it on a lift. All the people that are saying you can't do it with true duals under the axle are the people who aren't running them and have no expierence with them.

2000taws6

iTrader: (2)

Damn! That is my car and I can't believe all the crap people are talking about it. I have never had anything but compliments on my exhaust. People are bitching about all this crap that is untrue. I never bottom out. I have flanges at the x-pipe so I can take it down easily if I have to. You can jack the car up by the diff. and put it on jack stands also without taking the exhaust down. My brother has true duals over the axle and spent a lot more money only to have it rattle and bang on everything. No problems here. I think it looks mean. Thanks to all the people that had nice things to say about my car and screw all of you that say my car is ghetto.

2000taws6

iTrader: (2)

Here is my ghetto rig.

BlackScreaminMachine

iTrader: (17)

I dont care for it.

98Camarod

iTrader: (43)

LOL, ghetto....That **** is bad ***. I think I'm just going to have a polished 3" out the back once I can get it done.

3800RS

iTrader: (15)

I think that black ws6 looks pretty cool

lilbuddy1587

iTrader: (1)

That is ******* TOUGH looking. Really clean as well! Very nice bro

99Hawk262

iTrader: (19)

Yep, that's as ghetto as it gets . That's probably the best looking set-up I've seen. Very nice indeed .

2000taws6

iTrader: (2)

Thanks guys! I cant believe some of the crap people are saying. Whatever everyone has their own opinion.

Prerun4fun13

iTrader: (6)

Just dump it and call it a day, running under the axle is really ugly i hate to see hella exhaust under my car.