New guy with a Question!
#1
Thread Starter
Teching In
Joined: Feb 2008
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
From: Saint Charles, MO
New guy with a Question!
Okay so I was a die-hard Ford guy but since putting a lot of money in my old 1970 Mustang and still occasionally getting beat by a nicely modded LS1 I decided I would give it a try especially, since last time I was gonna buy an
LS1 I ended up getting a 96' Triple Black Cobra and, spent like 10,000 on it before I decided the miles were getting high and I came across this beautiful NBM M6 2000 TA Ram Air...I had to get it!! So I traded the 100,000 mile Cobra for the TA with only 30,000 miles! It now has 40,000 and I need more power! Only Mods are a SLP LID, SMOOTH BELLOW, and an ELECTRIC CUTOUT! About 8 Months ago I purchased SLP LONGTUBE HEADERS AND A Y-PIPE with HIGH FLOW CATS! I hesitated to install them since I just purchased a new house and wanted to get some money save for a safety net! I now have the money to install them but through reading in this very informative website, I have read some bad things about them and their clearance issue! Should I sell these and buy another brand??? I thought these were some of the best money could buy being ceramic coated and stainless steel! But I like to have my car washed through automatic carwashes occasionally,especially in the winter! Will I be able to have the Car Washed with these Headers! This really isn't the biggest concern, but more like a side note! The Main thing is ground clearance! What if I lower the Car! IF I SHOULD SELL THEM What other BRAND would be better!
ALSO, If I do the INSTALL and it is gonna need a tune should I remove my EGR , and what would be the Best CAM if I don't want to notch pistons or change heads do to the LOW MILES OF THE CAR!
Sorry for long post and your opinion is appreciated!
LS1 I ended up getting a 96' Triple Black Cobra and, spent like 10,000 on it before I decided the miles were getting high and I came across this beautiful NBM M6 2000 TA Ram Air...I had to get it!! So I traded the 100,000 mile Cobra for the TA with only 30,000 miles! It now has 40,000 and I need more power! Only Mods are a SLP LID, SMOOTH BELLOW, and an ELECTRIC CUTOUT! About 8 Months ago I purchased SLP LONGTUBE HEADERS AND A Y-PIPE with HIGH FLOW CATS! I hesitated to install them since I just purchased a new house and wanted to get some money save for a safety net! I now have the money to install them but through reading in this very informative website, I have read some bad things about them and their clearance issue! Should I sell these and buy another brand??? I thought these were some of the best money could buy being ceramic coated and stainless steel! But I like to have my car washed through automatic carwashes occasionally,especially in the winter! Will I be able to have the Car Washed with these Headers! This really isn't the biggest concern, but more like a side note! The Main thing is ground clearance! What if I lower the Car! IF I SHOULD SELL THEM What other BRAND would be better!
ALSO, If I do the INSTALL and it is gonna need a tune should I remove my EGR , and what would be the Best CAM if I don't want to notch pistons or change heads do to the LOW MILES OF THE CAR!
Sorry for long post and your opinion is appreciated!
#3
TECH Fanatic
iTrader: (7)
Joined: Mar 2007
Posts: 1,083
Likes: 0
Received 0 Likes
on
0 Posts
From: middle of nowhere, IL
in my opinion ditch the SLP's....if fitment, install ease, or ground clearance are important.
if you have the $$$ look at Kooks, American Racing, or QTP's
if you're on a budget, ceramic coated Hookers or even Armor Coat Pacesetters
if you have the $$$ look at Kooks, American Racing, or QTP's
if you're on a budget, ceramic coated Hookers or even Armor Coat Pacesetters
#4
TECH Addict
iTrader: (41)
Joined: Feb 2006
Posts: 2,003
Likes: 0
Received 0 Likes
on
0 Posts
From: Germantown Hills IL
congrats on your new car
SLP headers (i have em) will hang about an inch, to an inch and ahalf below the K member
i did not tune after my SLP install, saving that for after the H/C, my car runs fine,
EGR will throw a code if not removed via PCM once the actual hardware is removed
can't help ya with the cam, although,,i think we are safe under .600 lift without having to flycut,,but dont take my word on that
241's are pretty good heads (assuming thats what you have) u may want to consider just doing a PNP on your stock heads for some extra flow,,at a lot lower cost than buying 243's, aftermarkets, etc.
Congrats again on you new toy!!! (great choice in color too)
SLP headers (i have em) will hang about an inch, to an inch and ahalf below the K member
i did not tune after my SLP install, saving that for after the H/C, my car runs fine,
EGR will throw a code if not removed via PCM once the actual hardware is removed
can't help ya with the cam, although,,i think we are safe under .600 lift without having to flycut,,but dont take my word on that
241's are pretty good heads (assuming thats what you have) u may want to consider just doing a PNP on your stock heads for some extra flow,,at a lot lower cost than buying 243's, aftermarkets, etc.
Congrats again on you new toy!!! (great choice in color too)
Trending Topics
#8
Thread Starter
Teching In
Joined: Feb 2008
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
From: Saint Charles, MO
Back to the question...seems like Kooks is the definate winner in quality and performance and fitment....where would be a good place to get them and what should I sell the SLP's with High Flow Cats for?!
#9
Thread Starter
Teching In
Joined: Feb 2008
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
From: Saint Charles, MO
congrats on your new car
SLP headers (i have em) will hang about an inch, to an inch and ahalf below the K member
i did not tune after my SLP install, saving that for after the H/C, my car runs fine,
EGR will throw a code if not removed via PCM once the actual hardware is removed
can't help ya with the cam, although,,i think we are safe under .600 lift without having to flycut,,but dont take my word on that
241's are pretty good heads (assuming thats what you have) u may want to consider just doing a PNP on your stock heads for some extra flow,,at a lot lower cost than buying 243's, aftermarkets, etc.
Congrats again on you new toy!!! (great choice in color too)
SLP headers (i have em) will hang about an inch, to an inch and ahalf below the K member
i did not tune after my SLP install, saving that for after the H/C, my car runs fine,
EGR will throw a code if not removed via PCM once the actual hardware is removed
can't help ya with the cam, although,,i think we are safe under .600 lift without having to flycut,,but dont take my word on that
241's are pretty good heads (assuming thats what you have) u may want to consider just doing a PNP on your stock heads for some extra flow,,at a lot lower cost than buying 243's, aftermarkets, etc.
Congrats again on you new toy!!! (great choice in color too)
Are 241's referred to as stock LS1 heads and 243's are Z06 Heads!
#10
Thread Starter
Teching In
Joined: Feb 2008
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
From: Saint Charles, MO
I do have a QTP electric cutout that I am impressed with maybe there headers would be a good choice! Where would be a good place to buy either the QTP or KOOKS!
#11
Launching!
iTrader: (11)
Joined: Nov 2005
Posts: 264
Likes: 0
Received 0 Likes
on
0 Posts
From: Maryville, IL
Ya buying a first house will do that to ya! Makes you reconsider all of your expenses...lol. But I would say it has been a little too long! Its like buying a condom and never using it! Anyways looks like you sold your car and picked up an 02...was there something wrong with the 98?
Back to the question...seems like Kooks is the definate winner in quality and performance and fitment....where would be a good place to get them and what should I sell the SLP's with High Flow Cats for?!
Back to the question...seems like Kooks is the definate winner in quality and performance and fitment....where would be a good place to get them and what should I sell the SLP's with High Flow Cats for?!
#12
On The Tree
iTrader: (1)
Joined: Jul 2007
Posts: 185
Likes: 0
Received 0 Likes
on
0 Posts
From: Fort Worth TX
I personally just bought a set of american racing headers. I have heard only good things about them. I should be getting them in the mail today so i will let you know later how they are.
Kooks headers i have heard mostly good things about them, and a lot of the sponsers sell them. try looking at speed inc. they have pretty good prices.
qtp headers seems to me like they are a hit or miss on quality. when they first came out they were good, but now the quality just doesnt seem to be there.
Try searching, there is a lot of good info on here about headers.
my $0.02
Kooks headers i have heard mostly good things about them, and a lot of the sponsers sell them. try looking at speed inc. they have pretty good prices.
qtp headers seems to me like they are a hit or miss on quality. when they first came out they were good, but now the quality just doesnt seem to be there.
Try searching, there is a lot of good info on here about headers.
my $0.02
#15
LS1TECH & Trucks Sponsor
iTrader: (34)
On your LS1 you could have either 853 or 241 heads, there was a mid-year change. 243s are from the LS6 for the most part, but later model trucks got them as well.
We sell most brands of headers, let me know what you want and I'll see what SDPC can do for you!
We sell most brands of headers, let me know what you want and I'll see what SDPC can do for you!
__________________
800-456-0211 / PM / Facebook
WHIPPLE Superchargers, Procharger, Magnuson, Powerbond Sale, HPTuners packages!, Trickflow, AFR, PRC, CHE Trunion upgrade, $100 7.400" pushrod set, Custom Cam of your choice
800-456-0211 / PM / Facebook
WHIPPLE Superchargers, Procharger, Magnuson, Powerbond Sale, HPTuners packages!, Trickflow, AFR, PRC, CHE Trunion upgrade, $100 7.400" pushrod set, Custom Cam of your choice
#17
Thread Starter
Teching In
Joined: Feb 2008
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
From: Saint Charles, MO
How did it Run!!!!!!!!!!!! Was it a Manual! What type of numbers did you put down!..the only difference should be the intake, yours being and LS6 and mine a LS1. What other supporting mods did you have to get your numbers! I hear the MS4 is a great choice! at 603 lift would the MS3 be a better choice being it is my daily driver!
#18
Thread Starter
Teching In
Joined: Feb 2008
Posts: 33
Likes: 0
Received 0 Likes
on
0 Posts
From: Saint Charles, MO
VIN#....?
How much would some KOOKS cost me. Do they have a Ypipe that matches!
#20
Yes from what i have heard the MS3 and MS4 are both great cams. They are custom ground by comp cams......... They have videos of cars with the cams in them on youtube.. just search magic stick 3 or magic stick 4 on youtube .... I ahve not had a chance to run with it yet i am still worki on the car i am doin alot of mods to it...... My car is a automatic but i have beat alot of six or 5 speed cars...... But the cam is great from what i hear they sound good with mufflers and of course even better with cut outs... Now I got my headers from LS1 speed , they are a set of flowtechs that are ceramic coated for 373.00!!! A couple of my budies have got them and they sound great..... But as allways the choice is up to you, sometimes it is best to you with your own stuff and you might get a great setup out of them!!! Good Luck