Need help! H/C install
12-26-2005, 06:37 PM
#42
Originally Posted by SUX2BU
pul a plug wire see if theyre firing. and BTW there should be three grounds on the baxck of the driver side head.
12-26-2005, 06:52 PM
#44
SSU's Drunk Typing Whore
Thread Starter
iTrader: (47)
Join Date: Jan 2004
Posts: 4,609
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 777
If you know someone that has an f-body around you see if you can borrom their coil packs. That would eliminate that. I really don't see why the coil wouldn't be good.
They were off the car for a month or so...not sure if that has an effect on them?
12-26-2005, 07:29 PM
#46
SSU's Drunk Typing Whore
Thread Starter
iTrader: (47)
Join Date: Jan 2004
Posts: 4,609
Likes: 0
Received 0 Likes
on
0 Posts
Yeah I just loosened those two bolts for all three grounds. Repositioned all three grounds - they all were on tight and flush with the head. So I am sure that didnt do anything.
Maybe I took something off on accident when removing the AIR? I just throwing **** out there cause I really have no idea why there is no spark.
I mean the coils have to be good. All the grounds are in. All the sensors are in by the back of the intake manifold...but no spark.
I may pick up a mulimeter? was told that would check to see if the coils are working at all.
Maybe I took something off on accident when removing the AIR? I just throwing **** out there cause I really have no idea why there is no spark.
I mean the coils have to be good. All the grounds are in. All the sensors are in by the back of the intake manifold...but no spark.
I may pick up a mulimeter? was told that would check to see if the coils are working at all.
12-26-2005, 08:48 PM
#47
SSU's Drunk Typing Whore
Thread Starter
iTrader: (47)
Join Date: Jan 2004
Posts: 4,609
Likes: 0
Received 0 Likes
on
0 Posts
Here is how it was lined up... dot to dot.
So that cant be it.
https://ls1tech.com/forums/generation-iii-internal-engine/420603-look-good-you-guys.html
So that cant be it.
https://ls1tech.com/forums/generation-iii-internal-engine/420603-look-good-you-guys.html
12-26-2005, 09:54 PM
#48
Make sure ya didn't pop any fuses! Did ya make sure the cam sensor at the back is plugged in no spark = no signal to the pcm or If ya done checked the ground alot! You can also hook up a scanner and watch all the sensor to see what they do while you are spinning it over!
12-26-2005, 09:57 PM
#49
SSU's Drunk Typing Whore
Thread Starter
iTrader: (47)
Join Date: Jan 2004
Posts: 4,609
Likes: 0
Received 0 Likes
on
0 Posts
I have triple checked the fuses now. I wish it was that simple...hope it still is actually.
Yeah that badboy is plugged in, I felt around back there last night and tonight - its in there.
What kinda scanner? Multimeter?
Yeah that badboy is plugged in, I felt around back there last night and tonight - its in there.
What kinda scanner? Multimeter?
12-26-2005, 10:05 PM
#50
No scanner like one that reads codes and data of the sensors going to the pcm! If ya see something like no rpm when ya spin it over ya see that a wire like a sensor is un plugged or tighteded down and shorted maybe where ya can't see it that would tell ya everything there! The coils are very easy to get back on right its usually going to be some mistake thats weird some how I do a ot of electical stuff where I work and run into messed up wiring all the time! Most common is the wire tigned down under a bolt or nut and couldn't really see it but reading the sensor while spinning it over will tell ya a lot a direction to go in!I hate running problems but gotta get it fixed though sorry so long!@
12-27-2005, 09:04 PM
#54
You do all the testing yet! Speed eng is in CA isn't it have ya talked to them any!If ya ain't getting spark it should be easy to find (maybe)I seriously dought you fried all 8 coils heck mine has run with 4 only before because I forgot to plug them up so its either the cam sensor or pcm! Did ya scan the pcm and read the sensors ya going to be running in ciricles if not!
12-28-2005, 03:54 AM
#58
TECH Fanatic
Join Date: Jan 2003
Location: Northern Va
Posts: 1,094
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Lithium
Seriously man...I am just drinking some beers right now and trying not to think about it.
I am praying its something simple
I am praying its something simple
There's someone out there somewhere who has the answer- hang in there. 
12-28-2005, 10:35 PM
#60
SSU's Drunk Typing Whore
Thread Starter
iTrader: (47)
Join Date: Jan 2004
Posts: 4,609
Likes: 0
Received 0 Likes
on
0 Posts
Naw...nothing yet, still working on it. Have not had that much time due to work and all.
I bought a multimeter though and I have a buddy helping me out with that. So I am curious to see what going on with the coils.
Still praying!!!!!!!!
I bought a multimeter though and I have a buddy helping me out with that. So I am curious to see what going on with the coils.
Still praying!!!!!!!!