847? where?
#1
On The Tree
Thread Starter
iTrader: (24)
Join Date: Feb 2006
Location: Rockford, IL
Posts: 135
Likes: 0
Received 0 Likes
on
0 Posts
847? where?
well I have been trying to find out where I can pick up a 847 cam...
I have had hit a snag....went to Gm parts direct, they have this part number:12370847. is this the right cam? they have it measured with 1.5 rockers......
if it is the same cam....how can I go about ordering it? everytimeI go to find dealers....it says page cannot be found. any imput would help out dramaticly.
I have had hit a snag....went to Gm parts direct, they have this part number:12370847. is this the right cam? they have it measured with 1.5 rockers......
if it is the same cam....how can I go about ordering it? everytimeI go to find dealers....it says page cannot be found. any imput would help out dramaticly.
#3
If Jason is still doing this, it's the best deal other than used.
Jason Cromer: 877-726-8295 or 850-243-8826 (direct parts dept ph #)
email: gmparts@samtaylor.com
Sam Taylor Buick/Cadillac Ft. Walton Beach, FL
$209.00
* Crane Cam 109841 grind # HR-296-2S-12 IG (CAM) $209.00 from Jason
* KM# 16214681 $29.95 from Jason - 96 Corvette 5.7 L w/55 LT4 Knock Sensor
* Crane Kit #10308-1 (SPRING KIT)
Sam Taylor Buick/Cadillac
Attn: Jason Cromer
329 Miracle Strip Parkway
Ft. Walton Beach, FL 32548
* GM847 - Crane Cam 109841 grind # HR-296-2S-12 IG (CAM) - $209.00 from Jason
* Shipping (Next Day Air) - $45.00
* Total - $ 254.00
Jason Cromer: 877-726-8295 or 850-243-8826 (direct parts dept ph #)
email: gmparts@samtaylor.com
Sam Taylor Buick/Cadillac Ft. Walton Beach, FL
$209.00
* Crane Cam 109841 grind # HR-296-2S-12 IG (CAM) $209.00 from Jason
* KM# 16214681 $29.95 from Jason - 96 Corvette 5.7 L w/55 LT4 Knock Sensor
* Crane Kit #10308-1 (SPRING KIT)
Sam Taylor Buick/Cadillac
Attn: Jason Cromer
329 Miracle Strip Parkway
Ft. Walton Beach, FL 32548
* GM847 - Crane Cam 109841 grind # HR-296-2S-12 IG (CAM) - $209.00 from Jason
* Shipping (Next Day Air) - $45.00
* Total - $ 254.00
#4
Launching!
iTrader: (12)
Join Date: Feb 2006
Location: Maryland
Posts: 220
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by BRETTINATOR
If Jason is still doing this, it's the best deal other than used.
Jason Cromer: 877-726-8295 or 850-243-8826 (direct parts dept ph #)
email: gmparts@samtaylor.com
Sam Taylor Buick/Cadillac Ft. Walton Beach, FL
$209.00
* Crane Cam 109841 grind # HR-296-2S-12 IG (CAM) $209.00 from Jason
* KM# 16214681 $29.95 from Jason - 96 Corvette 5.7 L w/55 LT4 Knock Sensor
* Crane Kit #10308-1 (SPRING KIT)
Sam Taylor Buick/Cadillac
Attn: Jason Cromer
329 Miracle Strip Parkway
Ft. Walton Beach, FL 32548
* GM847 - Crane Cam 109841 grind # HR-296-2S-12 IG (CAM) - $209.00 from Jason
* Shipping (Next Day Air) - $45.00
* Total - $ 254.00
Jason Cromer: 877-726-8295 or 850-243-8826 (direct parts dept ph #)
email: gmparts@samtaylor.com
Sam Taylor Buick/Cadillac Ft. Walton Beach, FL
$209.00
* Crane Cam 109841 grind # HR-296-2S-12 IG (CAM) $209.00 from Jason
* KM# 16214681 $29.95 from Jason - 96 Corvette 5.7 L w/55 LT4 Knock Sensor
* Crane Kit #10308-1 (SPRING KIT)
Sam Taylor Buick/Cadillac
Attn: Jason Cromer
329 Miracle Strip Parkway
Ft. Walton Beach, FL 32548
* GM847 - Crane Cam 109841 grind # HR-296-2S-12 IG (CAM) - $209.00 from Jason
* Shipping (Next Day Air) - $45.00
* Total - $ 254.00
Thats a great deal. Next day air????
#5
On The Tree
iTrader: (4)
Join Date: Jun 2003
Location: so.cal
Posts: 193
Likes: 0
Received 0 Likes
on
0 Posts
I originally had ordered mine from summit, then they Emailed me and said it would take like 4-6 week's. SDPC got one to me in a couple of days.
http://www.sdpc2000.com/search.asp?s...0847&doquery=1
http://www.sdpc2000.com/search.asp?s...0847&doquery=1
#6
Originally Posted by Camaroguy22
Thats a great deal. Next day air????
#7
Launching!
iTrader: (12)
Join Date: Feb 2006
Location: Maryland
Posts: 220
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by BRETTINATOR
Then order it ups ground ...I had to do the install over a weekend, couple years back so I chose next day air.
I have delt with Jason before, great guy and great prices.
Just pointing out how expensive that method of shipping is. I would never spend that much to ship, I would rather plan out what I need to buy so I can do slow shipping and not pay a ton.
Trending Topics
#8
Originally Posted by Camaroguy22
I am not ordering an 847 cam.
I have delt with Jason before, great guy and great prices.
Just pointing out how expensive that method of shipping is. I would never spend that much to ship, I would rather plan out what I need to buy so I can do slow shipping and not pay a ton.
I have delt with Jason before, great guy and great prices.
Just pointing out how expensive that method of shipping is. I would never spend that much to ship, I would rather plan out what I need to buy so I can do slow shipping and not pay a ton.
#9
Launching!
iTrader: (12)
Join Date: Feb 2006
Location: Maryland
Posts: 220
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by BRETTINATOR
Yep...ohhh kay then...well I'm sure your reply to this thread really helped the mass population with knowing what you wouldn't do...
I am sure it did. It helps to have common sense in life and only spend 5$ on shipping vs 50$ with a little planning.
#12
TECH Regular
Join Date: Nov 2004
Location: league city,tx
Posts: 440
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Camaroguy22
I am sure it did. It helps to have common sense in life and only spend 5$ on shipping vs 50$ with a little planning.
#13
Originally Posted by Camaroguy22
I am sure it did. It helps to have common sense in life and only spend 5$ on shipping vs 50$ with a little planning.
B) Common sense has absolutely nothing to do with this, my cam toasted on a Wed, ordered parts on a Thur and by Fri evening I had what I needed to get my car running over a weekend.
Again you have enlightened us with absolutely nothing, if your going to post on a thread asking for advice then post useful advice & not your negative or immature comments.
#14
Originally Posted by GTP PWR
I just sent in an order through sdpc, thank you!!!!!!!
Good luck
#15
Launching!
iTrader: (12)
Join Date: Feb 2006
Location: Maryland
Posts: 220
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by BRETTINATOR
A) This guy asked for advice, like a couple others I provided a couple useful options.
B) Common sense has absolutely nothing to do with this, my cam toasted on a Wed, ordered parts on a Thur and by Fri evening I had what I needed to get my car running over a weekend.
Again you have enlightened us with absolutely nothing, if your going to post on a thread asking for advice then post useful advice & not your negative or immature comments.
B) Common sense has absolutely nothing to do with this, my cam toasted on a Wed, ordered parts on a Thur and by Fri evening I had what I needed to get my car running over a weekend.
Again you have enlightened us with absolutely nothing, if your going to post on a thread asking for advice then post useful advice & not your negative or immature comments.
My original post just was saying yuck to paying that much for shipping. You have to go and get all pissy with the punk rollseyes response. I can post in whatever thread I want as long as I am not breaking forum rules, I don't need your approval. My aim is not to enlighten or impress you. If you think that saying air shipping is expensive is immature, you need to go lock yourself in a box.
Last edited by Camaroguy22; 02-19-2006 at 07:03 PM.
#16
Launching!
iTrader: (12)
Join Date: Feb 2006
Location: Maryland
Posts: 220
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 95zpro
without knowing the reason why he had to do his rebuild over the weekend(I'm guessing because it's his daily driver) it seems kind of ridiculous to criticize someone for how they get parts. Most of us have had to rebuild or fix our cars when they broke over the weekend with some spirited driving in order to make it to work on Monday; it's just a part of it....Sorry to get off topic but just wanted to put in my two cents.
#17
On The Tree
Thread Starter
iTrader: (24)
Join Date: Feb 2006
Location: Rockford, IL
Posts: 135
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by BRETTINATOR
your going to love this cam dude, hopefully your using 1.6 RRs and good springs with it too, like the 306 this cam has made big gains in the LTs. Wish when I tore mine down it was damaged, was going to sell it for $100, but it was scarred from the thrown rod.
Good luck
Good luck
#18
11 Second Club
iTrader: (6)
Originally Posted by GTP PWR
thanks. I might add 1.7's to it as well. all my emissions crap is off the car now...so I'm not too worried about it. my next question is tuning....who would be able to tune my 94 PCM?
madz28
ed wright
Or try your self with tunercats..(Fun Fun)
#19
Originally Posted by GTP PWR
thanks. I might add 1.7's to it as well. all my emissions crap is off the car now...so I'm not too worried about it. my next question is tuning....who would be able to tune my 94 PCM?
Before there was a known issue with CompRs I collapsed one running Comp ProMag SS 1.7s with the Crane 99893 springs.
#20
On The Tree
Thread Starter
iTrader: (24)
Join Date: Feb 2006
Location: Rockford, IL
Posts: 135
Likes: 0
Received 0 Likes
on
0 Posts
thank you for the info on the springs/lifters. I'm thinking about buying the AFR 210 heads to go along with this setup. is this a good choice? I'm going off my friends 383....he bought them and Loves them.
what lifters do you have now? I have a collapsed one in mine right now...luckily I am not driving it till summer.
what lifters do you have now? I have a collapsed one in mine right now...luckily I am not driving it till summer.
Last edited by GTP PWR; 02-20-2006 at 02:10 PM. Reason: asking more of a question