replace pilot bearing?
#1
TECH Regular
Thread Starter
iTrader: (9)
Join Date: Mar 2007
Location: Hellertown, PA
Posts: 409
Likes: 0
Received 0 Likes
on
0 Posts
replace pilot bearing?
i'm going to be doing an ls7 clutch in my car next week probly. i wanted to see if you think its worth it to replace the pilot bearing or not? cars got 50k doesnt seem to make noise. and if so how do i go about replacing it i heard its a real pain in the ***. i also work at a gm dealership and we dont have the J tool to replace it
#5
12 Second Club
iTrader: (28)
Join Date: Feb 2005
Location: Quad Cities, IA
Posts: 858
Likes: 0
Received 0 Likes
on
0 Posts
Here's my theory... There's no reason to replace it that early to begin with (its a roller needle bearing style bearing) so it's not like an old style that is just greased up. Next, if you don't have the right tools and knowledge to do it, you might as well leave well enough alone. But all of that is just my .02 cents!
#6
TECH Regular
Thread Starter
iTrader: (9)
Join Date: Mar 2007
Location: Hellertown, PA
Posts: 409
Likes: 0
Received 0 Likes
on
0 Posts
Here's my theory... There's no reason to replace it that early to begin with (its a roller needle bearing style bearing) so it's not like an old style that is just greased up. Next, if you don't have the right tools and knowledge to do it, you might as well leave well enough alone. But all of that is just my .02 cents!
#7
TECH Fanatic
iTrader: (12)
Join Date: Oct 2006
Location: Orlando, FL
Posts: 1,724
Likes: 0
Received 0 Likes
on
0 Posts
Replace it man. While you have the tranny out you might as well.
I used a generic pilot bearing remover and a slide hammer.
If it doesn't come out easily just use a hammer and a chisel to cut the bearing in half. Just make sure the chisel is smaller than the bearing diameter so you dont make contact with the crankshaft.
I used a generic pilot bearing remover and a slide hammer.
If it doesn't come out easily just use a hammer and a chisel to cut the bearing in half. Just make sure the chisel is smaller than the bearing diameter so you dont make contact with the crankshaft.
Trending Topics
#8
Here's my theory... There's no reason to replace it that early to begin with (its a roller needle bearing style bearing) so it's not like an old style that is just greased up. Next, if you don't have the right tools and knowledge to do it, you might as well leave well enough alone. But all of that is just my .02 cents!
I just did mine on a 2002 and it was not a roller bearing. This should be replaced everytime you do the job. Mine came apart and almost messed up my input shaft. The input seal started leaking and ruined my clutch. I would say put in a new roller style bearing while you are there.
#9
12 Second Club
iTrader: (3)
Join Date: Apr 2008
Location: Aimwell, La
Posts: 123
Likes: 0
Received 0 Likes
on
0 Posts
It is a cheap part and is alot of trouble to get to later if it starts making noise or goes out and it keeps the wobble out of the input shaft on trans. Saves trans. While I had it down I would do it. I did mine about a month ago. Tools $18 for the tool and $20 for the slide hammer at autozone and you can return them and get your money back.
#10
TECH Regular
Thread Starter
iTrader: (9)
Join Date: Mar 2007
Location: Hellertown, PA
Posts: 409
Likes: 0
Received 0 Likes
on
0 Posts
so u just need a slide hammer to get it out? i'd just rather not freak it up and not be able to get it out of there. if it turns ok and feels ok i might just let it alone since i was told by the gm dealership the chances of getting it out of there are slim
#11
Teching In
iTrader: (2)
Join Date: Mar 2008
Location: Marathon,Fl
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
just curious.. how tight is the pilot bearing suppose to be on the input shaft because my pilot bearing was all fucked up, needles everywhere, and the input shaft looks pretty burned like it was moving around... im just tryin to figure if the input shaft is bad or not... when i tried the new pilot bearing it slides on easy....
Last edited by camaroride32; 05-10-2008 at 04:42 PM.
#14
TECH Fanatic
iTrader: (12)
Join Date: Oct 2006
Location: Orlando, FL
Posts: 1,724
Likes: 0
Received 0 Likes
on
0 Posts
Just break it so it looses all its strength and then clean out the back of the crankshaft so no metal is left behind.
#15
Launching!
iTrader: (25)
Join Date: Jan 2006
Location: Hamilton Twp, NJ
Posts: 233
Likes: 0
Received 0 Likes
on
0 Posts
Replace it man. While you have the tranny out you might as well.
I used a generic pilot bearing remover and a slide hammer.
If it doesn't come out easily just use a hammer and a chisel to cut the bearing in half. Just make sure the chisel is smaller than the bearing diameter so you dont make contact with the crankshaft.
I used a generic pilot bearing remover and a slide hammer.
If it doesn't come out easily just use a hammer and a chisel to cut the bearing in half. Just make sure the chisel is smaller than the bearing diameter so you dont make contact with the crankshaft.
Attached are a few pics of the tool I used.
Chris
Last edited by 1QWIKBIRD; 05-10-2008 at 05:47 PM.
#16
12 Second Club
iTrader: (3)
Join Date: Apr 2008
Location: Aimwell, La
Posts: 123
Likes: 0
Received 0 Likes
on
0 Posts
That is the tool. It is usually pretty tight in the back of the crank and soaking it is a good idea. I have read where people also took a dremel tool and cut it in half to get them out if all else fails or no tools are available.
#19