Calling member warriorcustoms - LS1TECH - Camaro and Firebird Forum Discussion



Negative Trader Feedback Disputes| Fraud Reports | Scam Warnings

Calling member warriorcustoms

Reply
 
Thread Tools Search this Thread
Old 09-22-2016, 05:10 AM   #1
Staging Lane
Thread Starter
iTrader: (8)
 
Twin_Turbo's Avatar
 
Join Date: Dec 2011
Posts: 94
Default Calling member warriorcustoms

Hey Darian ....., why do you not reply to ebay or email messages?

I bought a good slightly used cam motion custom roller cam from you.
This cam was just what I needed for my high revving 396 build (callies 3.875 crank, pankl billet rods, je custompistons, splayed main reworked roller block etc, dart pro1 230s,jesel shaft rockers, unik short runner individual runner stack EFI system, 2" into 3.5" headers...etc etc)

I figured hell, I can save a few dolalrs here...but man what a costly mistake.

I took delivery of the cam after sitting in my parts pile to be shipped to me (I'm in the Netherlands) and my buddy didn't inspect the cam too carefully, he said it was there sealed and looked good. So I gave you pos feedback. Wnyway, it's not good. IT's junk, 2 lobes are bad and you HAD to know this, it's just plain obvious. You can not sell people junk like this for top dollar.

these are your ebay pics
https://lh3.googleusercontent.com/V_...20-h1080-rw-no

https://lh3.googleusercontent.com/fy...20-h1080-rw-no


https://lh3.googleusercontent.com/U_...20-h1080-rw-no

clever photography

this is the piece of junk you sold me for 200 dollars
+ shippibg and gas money

https://lh3.googleusercontent.com/SZ...20-h1080-rw-no

https://lh3.googleusercontent.com/wZ...20-h1080-rw-no

https://lh3.googleusercontent.com/8r...20-h1080-rw-no

You said you were going to use this on your 396 build, I think you got it cheap somewhere and decvided it was a good way to defraud someone of his hard earned cash.

I made 3!!! payments, one for the agreed price, more for shipping and then some for you needing a little more because of paypal fees and what not.
Paid with
MCARD x-0834
You'll see "PAYPAL *WARRIORCUST WARRIORCUST" on your card statement.
Exchange rate
219,62 EUR = 230,00 USD
1 Euro = 1,05 US Dollar
Sent to
Karsten Neuhaeuser
16579 CORNER LAKE DR
Orlando, FL 32820
United States
Track your delivery
27 January 2016, Marked as shipped
Status: Shipped
Transaction ID
42405502FF062473L
Seller information
Darian .... ‏(warriorcustoms1972‏)
[email protected]
Your purchase
SBC/LT1 solid roller cam...230,00 USD
Item #181997074978
Postage and Packaging0,00 USD
Tax0,00 USD
Purchase total230,00 USD
Fee0,00 USD
Total230,00 USD

Paid with
MCARD x-0834
You'll see "PAYPAL *WARRIORCUST WARRIORCUST" on your card statement.
Exchange rate
25,10 EUR = 26,28 USD
1 Euro = 1,05 US Dollar
Transaction ID
4CD974641P1024537
Sent to
Darian ......
[email protected]
Details
Sent to Darian .... 25,00 USD
Fee1,28 USD
Total26,28 USD

Paid with
MCARD x-0834
You'll see "PAYPAL *WARRIORCUST" on your card statement.
Transaction ID
4CF380233N623063W
Sent to
Darian .....
[email protected]
Note to Darian A......
additional funds
Details
Sent to Darian ....41,00 EUR
Fee1,95 EUR
Total42,95 EUR

Last edited by Twin_Turbo; 09-22-2016 at 07:16 AM.
Twin_Turbo is offline   Reply With Quote
Old 09-22-2016, 05:28 AM   #2
Staging Lane
Thread Starter
iTrader: (8)
 
Twin_Turbo's Avatar
 
Join Date: Dec 2011
Posts: 94
Default

https://ls1tech.com/forums/lt1-lt4-m...l#post18185194

Quote:
Originally Posted by warriorcustoms View Post
My 396 LTx build will be gettin twin 255s... The 2nd pump will be wired to come on when I arm the nitrous I thought I was pushin the "Street Drivin" limits with a Cam Motions SR thats 25x/26x @.05 .686/.662 112 & hand ported 200cc Dart Pro 1s that finished right at 208cc & 311cfm LoL Mines settin in pcs out in the Shop waitin on Me to get More Money LoL
Hope your gettin an S60 rear diff & a built 4L80E too!!! Youll need em!!! My Horsepower est came out to 640.6 on motor & then whatever I spray LoL In GM High Tech they built a 396 SBC a few yrs back with the same heads as mine with a 242 @.05 SR grind that made 603hp at the flywheel if that helps ya any... I still gotta buy my custom JE flat top nitrous pistons & shaft mount roller rockers before I can tell ya what My junk cranks out!!!
That's the cam right there in your post. Bragging about it.

and here
https://ls1tech.com/forums/lt1-lt4-m...l#post16732551

Quote:
Originally Posted by warriorcustoms View Post
My combo should peak around 6800 with a 25x/26x @ .05 .6xx Solid Roller So the 242 @ .05 will be close to that IF it wants more I guess I will need to Upgrade to an aftermarket set up Torque will sling you out of the corners With a 383 or 396 that larger solid roller cam will be more streetable More stroke is a good thing Theres no replacement for displacement!!! With a 3.6x crank that 25x duration cam will wanna spin to the moon Where the 3.875 will move the RPM down lower IT will hit the stock 7k limiter though LoL
https://ls1tech.com/forums/lt1-lt4-m...l#post16822540

Quote:
Originally Posted by warriorcustoms View Post
My Cam Motions Solid Roller is 255/262 @ .05 with .686/.662 lift Im sure those guys have one in the high 230s Mine will be in my 396 though Wouldnt run that in a 355
Twin_Turbo is offline   Reply With Quote
Old 11-30-2016, 02:10 AM   #3
TECH Resident
iTrader: (10)
 
warriorcustoms's Avatar
 
Join Date: Oct 2011
Location: Oklahoma
Posts: 929
Default

I bought that cam off here & never installed it... I checked Every Lobe before shipping to make sure the thing wasnt Rusted from setting in the closet for 2yrs & it was Good!!! Then like 4 mos After the Sale You send Pics that look like You Ran it with the Smaller Springs I tried to talk You out Of doin & It looks like You Valve Floated the ****** thing!!! I was gonna use it in My 396 but didnt wanna have Valve Springs as a Yearly Maint. regumate with those Aggressive Ramps!!! Thats Why I Sold it Not because it was fucked Up You Did that On Yer End!!! So **** Off My Trader Rating on Here is Flawless ****** Cry Baby...
warriorcustoms is offline   Reply With Quote
Old 01-10-2017, 05:37 AM   #4
Staging Lane
Thread Starter
iTrader: (8)
 
Twin_Turbo's Avatar
 
Join Date: Dec 2011
Posts: 94
Default

I never ran the thing. The cam was lying at my buddies to ship with the rest of my stuff. The engine isnt even complete. And I never intended to run small springs. I have 700 lift capable ultra ckean wire springs.

You never checked it or are ffing blind. These lobes were worn as shown when it got here. If I wrecked it myself I would not have opened a complaint. You purposely photographed it at such an angle that the messed up lobes are not visible. For instance the last lobe before the gear conveniently aimed down so the troughing/brinneling is not visible.

When I sent you pics of the worn lobes you said you couldnt see anything in the small pics. They were 1600 resolution. More testimony that you must be blind.

You are simply a crook selling off junk you bought for cheap at top dollar. BSing you ran it in your awesome 396. All lies... it never ran. Just a closet full of junk bullshit and pipe dreams.

I hope you choke in your rip off money you *****.

Last edited by Twin_Turbo; 01-10-2017 at 05:51 AM.
Twin_Turbo is offline   Reply With Quote
Old 01-10-2017, 05:57 AM   #5
Staging Lane
Thread Starter
iTrader: (8)
 
Twin_Turbo's Avatar
 
Join Date: Dec 2011
Posts: 94
Default

Heres your BS ....
Attached Thumbnails
Calling member warriorcustoms-screenshot_20170110-125249.png   Calling member warriorcustoms-screenshot_20170110-125309.png  
Twin_Turbo is offline   Reply With Quote
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
70 RSZ28 Camaro 5.3 Turbo Build Noahf Conversions & Hybrids 86 11-22-2016 12:52 PM
Parting 1998 tee-top 6 speed camaro (engine/trans gone) jakeb Parts Classifieds 25 10-04-2016 06:37 AM
Jarren_b ( guys is there not a member feedback section ? ) skeet Negative Trader Feedback 8 02-25-2016 01:34 AM
cam install and dyno results itsdaveonline Cadillac CTS-V 2004-2007 (Gen I) 40 06-11-2015 04:41 PM


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -5. The time now is 01:51 PM.