Huge Lt1/Tpi/SBC performance part sale(C4 vette parts, Wiseco, K1, Comp Cams & more)
01-09-2011, 10:49 PM
#1
Launching!
Thread Starter
iTrader: (7)
Join Date: Jan 2004
Location: In The Fast Lane
Posts: 219
Likes: 0
Received 0 Likes
on
0 Posts
Huge Lt1/Tpi/SBC performance part sale(C4 vette parts, Wiseco, K1, Comp Cams & more) Category: Drivetrain
Price: $50
Part Fits: 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird, Corvette, 67-92 Chevrolet Camaro, 67-92 Pontiac Firebird
Location (State): OH
Item Condition: Brand New
Shipping Information: Item Can be Shipped
Engine: LT1/LT4, Small Block
LS Engine?: Non-LS Part
These are parts from a C4 build that was cancelled and other lt1/sbc parts I have.
Here we go:
Wiseco Custom Pistons for a 388ci. These are some awesome pieces.
These are made for a 4.060" bore, 3.75" stroke, and 6.0" rod at a deck height of 9.015"(.010" under stock). They run Wiseco's GFX ring package which are .048" top and second compression rings with a 3mm oil ring utilizing a oil groove retention ring and the 15 deg pressure seal(same as Pro-Stock). These pistons were built with a 13.5:1 compression in a 58cc head. They are 2618 alloy forged. They have the best CERAMIC heat bearier dome coatings($80 per piston) and xylan permanent skirt coating($25 per piston) and have been lateral gas ported. They were built for high rpm road racing/drag racing and also designed to take a 150hp shot of nitrous on 2-mile speed trap events. Also included are the upgraded tool steel pins. The rings are already pre-gapped. The pistons are installed on New K1 Billet 6.0" rods in the pics(which are available together).
If the pistons are bought seperate, new spiro-locks will be included. I have a receipt of $1650 for these pistons, they have everything Wiseco could throw at them. Price with rods($585 new) is $1200 shipped(add $50 if you want new piston rings) or just Pistons for $750 Shipped(again add $50 for new rings).
Exotic Muscle long tube headers with AIR fittings for C4 vette. They have 1 3/4" primarys and 3" collectors. We just got them back from having v-band clamp ends put on and the Polydyn Heat bearier coating. The headers were used for about 5K miles before the above mods were added. They are in great shape!!! $500 Shipped (used vbands from another build will be included but are a little bent.)SOLD!!!!
Brand New Fidanza aluminum flywheel for C4 Vette. $275 Shipped
4-bolt Main corvette block from 1996 collectors edition vette. Needs a complete machine shop rework, was told .030" over will clean it up. Car had 34K miles when it was wrecked, cylinders have some surface rust on them, have had it oiled since i got it. We bought this block as a stand-bye block. $350
Brand New K1 4340 crank. 3.625 stroke crank, 2pc rear main. $635 when I purchased it, now only $500 Shipped SOLD!!!!
Brand New K1 Billet 6.125" rods with arp bolts. $585 when I purchased them, now only $450 Shipped(sorry no pics, will add later).SOLD!!!
NOTE: If you bought the 3.625" crank and 6.125" rods, you can use any pistons from a 396ci shelf part(3.875" crank and 6.0" rod). Wiseco has 3 shelf parts that can be used. The 3.625" crank(370ci) paired with the 6.125" rod will give you a great rod to stroke ratio for high rpm use and less skirt scrub than a stock 350 which prolongs the motor.
Brand New Custom Billet Solid Roller Cam from Comp Cams. The cam has the Everwear gear on it. Specs of cam are: 254/262, 108 lobe seperation, .622"/.612" lift with 1.6" rockers minus the .016" intake and .020" exhaust lash, everwear gear, 5/7 swap, 4876x/4221x ground on zero advance. Paid $400, asking $260 shipped.
Brand New Comp Cams Endure-x 873-16 Solid Roller lifters with +.300 lentgh for tpi/lt1 blocks. These are the updated versions with the Pin Oiling. Paid $510, asking $350 shipped.
Lunati 5.7" I-beam rods, these were installed but the motor never ran, would suggested using new rod bolts but these are included. $150 shipped.SOLD!!!!
Brand New: Split Second VC2 voltage clamp to massage the MAF. $50 Shipped (splitsec.com)
PayPal Only unless cash on pickup.
Located 30 miles east of Cleveland Ohio.
If you want to personally talk, pm me with your number with times to call as I work 2nd shift so it is hard to take calls.
Thanks
Steve
Last edited by insanez; 01-29-2011 at 03:43 PM.
Trending Topics
01-21-2011, 08:51 AM
#8
Bump for an honest guy. InsaneZ helped me build the exact 3.625" stroke, 6.125" rod combo 370CI that hes selling in pieces here, Its a beast of a setup and whoever buys all this will love it!
01-21-2011, 09:09 AM
#10
Launching!
Thread Starter
iTrader: (7)
Join Date: Jan 2004
Location: In The Fast Lane
Posts: 219
Likes: 0
Received 0 Likes
on
0 Posts
Thanks trick450r.
I actually sold the 370 stuff already. But I do have a K1 3.75 crank with 1pc seal for sale too, it's brand new, I have decided to go even bigger. With the heads my buddy and I had built, I need cubes. Thanks for the compliment too, it's much appreciated.
Lunati rods pending.
I actually sold the 370 stuff already. But I do have a K1 3.75 crank with 1pc seal for sale too, it's brand new, I have decided to go even bigger. With the heads my buddy and I had built, I need cubes. Thanks for the compliment too, it's much appreciated.
Lunati rods pending.
