2001: A CoreyD TA
#441
TECH Resident
Thread Starter
iTrader: (9)
Pic wasn’t working in last post. Fixed it. Also got first prototype for TA vent pod. Going to be tricky to get it to not spin around, but I have something in mind.
Also ran a scat pack challenger last night, not sure what he had done other than exhaust. He pulled up next to me revving and he honked it off. Did like a 65 roll and I had him by a car at 100. I guess he wasn’t happy because he hastily took the next exit lol
Also ran a scat pack challenger last night, not sure what he had done other than exhaust. He pulled up next to me revving and he honked it off. Did like a 65 roll and I had him by a car at 100. I guess he wasn’t happy because he hastily took the next exit lol
The following 3 users liked this post by CoreyD:
The following 2 users liked this post by CoreyD:
LaBLKv6Z (01-10-2023), ramairjohn2000 (01-09-2023)
The following 3 users liked this post by CoreyD:
The following users liked this post:
CoreyD (02-13-2023)
#448
TECH Resident
Thread Starter
iTrader: (9)
Successful day at the junkyard!
used a harbor freight windshield removal tool and sawed off this sail panel off a 96. Took maybe an hour total with breaks but once we got the wire hot it was moving. Deciding if I should DIY paint like my mirrors or take it somewhere. Not in a huge rush.
also found these ttop rubber trims in good shape on the same car. I’m going to model them and try my hand at printing some in TPU for whoever
Still on the lookout for a new steering wheel
The following 2 users liked this post by CoreyD:
blackbyrd (02-25-2023), ramairjohn2000 (02-25-2023)
#449
TECH Veteran
iTrader: (14)
You should have said something!!!! About a month ago I sold off my factory wheel it was mint.
Still have the airbag piece though.
Good find on the junkyard roof. That's gonna be on my shortlist mine is looking pitiful. The magg part is so expensive too
Still have the airbag piece though.
Good find on the junkyard roof. That's gonna be on my shortlist mine is looking pitiful. The magg part is so expensive too
The following 2 users liked this post by CoreyD:
blackbyrd (03-02-2023), ramairjohn2000 (03-03-2023)
The following 4 users liked this post by CoreyD:
89ThirdGenCamaro3310 (03-04-2023), LaBLKv6Z (03-06-2023), ramairjohn2000 (03-03-2023), Wraith99 (03-03-2023)
#456
TECH Resident
Thread Starter
iTrader: (9)
Fresh paint on the daily! Clear coat on the 4Runners hood has been quickly deteriorating. It was looking bad bad. Was lucky to find a body shop that could squeeze me in and had me in and out in a few days 👌
The following users liked this post:
blackbyrd (03-14-2023)
#457
TECH Resident
Thread Starter
iTrader: (9)
New steering wheel! OG one was thrashed and sun damaged real bad. Picked up this Camaro wheel. Didn’t realize until recently the camaro wheels were a little thicker and had ribbing.
also working on a driver side vent for camaros. First attempt looking good. Need to make a couple changes then will have a working piece
The following users liked this post:
ramairjohn2000 (03-15-2023)
The following 2 users liked this post by CoreyD:
LaBLKv6Z (03-15-2023), ramairjohn2000 (03-15-2023)
The following users liked this post:
CoreyD (03-16-2023)
#460
TECH Enthusiast
New steering wheel! OG one was thrashed and sun damaged real bad. Picked up this Camaro wheel. Didn’t realize until recently the camaro wheels were a little thicker and had ribbing.
also working on a driver side vent for camaros. First attempt looking good. Need to make a couple changes then will have a working piece