unmilled - LS1TECH - Camaro and Firebird Forum Discussion - Threads Tagged with unmilled

LS1TECH - Camaro and Firebird Forum Discussion
Tags
Threads Tagged with unmilled

Threads Tagged with unmilled

Thread / Thread Starter

Last Post

Replies

Views

Forum

25, 53, 60, factory, heads, lq4, ls1tech, ls6, prc, site, stage, stock, tsp, unmilled, yellowbulletcom

prc 2.5 stage 5.3 heads on an lq4

MasRapidoMateo on 02-11-2013

05-16-2013 05:03 PM
by squirlNUTZ

Go to last post

6

10,947

Generation III Internal Engine

243s, 317s, ls1, ls2, shroud, unmilled, valve

Should I dump my 243s for 317s?...

(

Multi-page thread

1 2)

Snyper on 11-07-2009

11-10-2009 07:33 PM
by elias_799

Go to last post

24

1,864

Forced Induction

243, cam, good, ls1tech, ms4, mti, nitrious, nitrous, torquer, unmilled, v2, vidicator, vindicator, work, x1

vindicator or ms4?

(

Multi-page thread

1 2)

dubrado on 11-18-2008

11-20-2008 03:59 PM
by lemons12

Go to last post

22

2,972

Generation III Internal Engine

040, 228r, 25, 53, 53l, bump, cam, compression, gasket, gaskets, head, heads, mls, prc, thinner, thinning, unmilled

PRC 5.3 heads...can I run a thinner gasket??

Raise on 08-20-2008

08-22-2008 12:09 AM
by Empatho

Go to last post

12

796

Generation III Internal Engine

Largest cam that'll fit my current heads/springs setup...

VIPERBLUELX on 07-10-2008

07-12-2008 09:25 PM
by TXZ28LS1

Go to last post

18

1,237

Generation III Internal Engine

040, 243, 243s, gasket, ls1tech, milled, push, pushrods, rods, size, unmilled

what size pushrods with unmilled 243 and .040 gasket

TXsilverado on 12-06-2007

12-07-2007 11:29 AM
by JPH

Go to last post

5

537

Generation III Internal Engine

big, cam, heads, l92, ls1, milled, unmilled, versus

Small cam+milled heads vs Bigger cam and unmilled heads? Discuss

phoenix1987 on 12-05-2007

12-06-2007 10:42 AM
by Ragtop 99

Go to last post

6

1,161

Generation III Internal Engine

220, cam, cams, cast, flow, heads, l76, length, medium, needed, pushrods, trick, unmilled

Trickflow Heads & Small to Medium Cams

(

Multi-page thread

1 2)

Pewterme on 08-28-2007

09-03-2007 09:17 PM
by allthrotle

Go to last post

24

5,887

Generation III Internal Engine

243s, clear, ported, unmilled, vindicator

Guru's.. CAM opinion wanted, and Will this fit?

Asmodeus on 08-24-2007

08-24-2007 09:49 PM
by Asmodeus

Go to last post

7

785

Generation III Internal Engine

205, 373, 60l, afr, c5, gm, heads, iron, ls, motor, turbo, unmilled

Best heads for turbo motor?

NassyVette on 07-12-2006

07-14-2006 12:35 PM
by MiaSSmaro98

Go to last post

13

1,043

Forced Induction

030, 244, afr, aluminum, cam, f13, head, heads, ls1, ls1tech, milled, milling, unmilled

question about milling AFR heads with F13 cam

(

Multi-page thread

1 2)

WS6FirebirdTA00 on 03-16-2005

03-23-2005 09:43 PM
by Tony Mamo @ AFR

Go to last post

27

1,557

Generation III Internal Engine

03, 05, 2003, 53, 53l, chambers, compression, gasket, head, heads, ls1, milled, milling, ratio, truck, unmilled

Un-milled 5.3 truck head = what compression ratio?

needmoremoney on 05-05-2003

05-08-2003 09:35 PM
by Tin Indian

Go to last post

3

660

Generation III Internal Engine

53, compression, heads, unmilled

Compression using 5.3 unmilled heads?

Bad1le on 10-17-2002

10-18-2002 12:06 AM
by ls1290

Go to last post

1

554

Generation III Internal Engine

All times are GMT -5. The time now is 01:05 AM.