FS/FT Warwagon Pitcart/Toolbox
07-14-2009, 11:25 AM
#1
6600 rpm clutch dump of death Administrator
Thread Starter
FS/FT Warwagon Pitcart/Toolbox I have a new toolbox I'm looking to get rid of. I'd be willing to trade it for an engine. Its a NASCAR Style War Wagon built by Delson Pitcarts.
http://www.delsonproducts.com
Here is a picture of it. I can deliver it in the Houston area. Outside of Houston. I can also arrange the shipping as I have a big discount on shipping (73%) with UPS Freight.
The Box new was over $6500. The box was used for a short time to keep some electronic componenets, and has not been used since. I do not believe it has ever had a tool in any of the drawers.
the rear storage area has a hydraulic lift in it currently. That can be swapped out for shelving, or for hose reels. It has storage on the backside of the cart for liquids like containers of oil, spray paint, etc...
I'm asking $6000 OBO, trades for a built motor, or even trades for components (heads, crank, blocks, etc...)
The box is 60" long. 30" deep, and I think about 44" tall.
12 gauge steel top
2" high formed back stop at rear of steel top
16 gauge cabinet construction
16 gauge drawer shell construction
Drawers, each rated at 250 lbs capacity
Full length, massive ball bearing slides on drawers
Extruded aluminum drawer pulls with lock in place, peel back plastic strips to cover drawer labels
One end cabinets and one back cabinet
Two removable shelves in end cabinets
Two adjustable baskets in back cabinet
Stainless steel, lockable, slam latch on each cabinet doors
Full length stainless steel piano hinges on cabinet doors
Ribbed rubber matting on all work surfaces, drawers and shelves
Drawer section lockable as a unit
High security locks
Powder coated on all surfaces
http://www.delsonproducts.com
Here is a picture of it. I can deliver it in the Houston area. Outside of Houston. I can also arrange the shipping as I have a big discount on shipping (73%) with UPS Freight.
The Box new was over $6500. The box was used for a short time to keep some electronic componenets, and has not been used since. I do not believe it has ever had a tool in any of the drawers.
the rear storage area has a hydraulic lift in it currently. That can be swapped out for shelving, or for hose reels. It has storage on the backside of the cart for liquids like containers of oil, spray paint, etc...
I'm asking $6000 OBO, trades for a built motor, or even trades for components (heads, crank, blocks, etc...)
The box is 60" long. 30" deep, and I think about 44" tall.
12 gauge steel top
2" high formed back stop at rear of steel top
16 gauge cabinet construction
16 gauge drawer shell construction
Drawers, each rated at 250 lbs capacity
Full length, massive ball bearing slides on drawers
Extruded aluminum drawer pulls with lock in place, peel back plastic strips to cover drawer labels
One end cabinets and one back cabinet
Two removable shelves in end cabinets
Two adjustable baskets in back cabinet
Stainless steel, lockable, slam latch on each cabinet doors
Full length stainless steel piano hinges on cabinet doors
Ribbed rubber matting on all work surfaces, drawers and shelves
Drawer section lockable as a unit
High security locks
Powder coated on all surfaces
Last edited by J-Rod; 03-31-2010 at 02:45 PM.
07-15-2009, 09:09 AM
#3
6600 rpm clutch dump of death Administrator
Thread Starter
thanks.... 
Forgot to add that I will also consider trades on GenI and early Gen II Camaros (67-72), along with 66-72 Novas.
Forgot to add that I will also consider trades on GenI and early Gen II Camaros (67-72), along with 66-72 Novas.
07-17-2009, 10:27 AM
#5
6600 rpm clutch dump of death Administrator
Thread Starter
I will also consider trades for:
A Built LSx motor (347,4xx, etc...) or componenents
86-87 GN T-Type Roller
67-72 Camaro
67-72 Nova
A Built LSx motor (347,4xx, etc...) or componenents
86-87 GN T-Type Roller
67-72 Camaro
67-72 Nova
