When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Didn't think this warranted starting a new thread. But would you guys use this aftermarket front crank seal?
It looks a little nasty up close and isn't quite perfectly round in the centre. It is marked as 'Jago' and it may have come out of a victor reinz gasket kit. Could be fine but never fitted one of these previously.
Didn't think this warranted starting a new thread. But would you guys use this aftermarket front crank seal?
It looks a little nasty up close and isn't quite perfectly round in the centre. It is marked as 'Jago' and it may have come out of a victor reinz gasket kit. Could be fine but never fitted one of these previously.
I have not tried that particular seal, but there has been many parts over the years that I have refused to use just because they did not look up to par.
I have not tried that particular seal, but there has been many parts over the years that I have refused to use just because they did not look up to par.
Yeah I ended up deciding to order a bunch of stuff from Summit, including an OE seal.
that car 60's hard for being so big. you're running a 200-4R, right? what was the DA?
Yes. 200-4R with a Circle D 4c stall converter that flashes to roughly 4000 n/a. The d/a barely crept into the negatives at the end of the night. about -90. It was about 57-58 degrees.
Yes. 200-4R with a Circle D 4c stall converter that flashes to roughly 4000 n/a. The d/a barely crept into the negatives at the end of the night. about -90. It was about 57-58 degrees.
Congrats on continuing to improve! I'm getting close to calling Circle D about a new converter for my Camaro. I'm looking for something a little tighter for nitrous passes with the added benefit of being a little more street-driver friendly as well. I was concerned about losing some in the 60' on the motor but your car out 60's mine on the motor with your 9.5inch 4000 stall. Of course I'm probably wasting a lot of energy with all the upward motion. Congrats again!
Awesome times!! Been following that car for a long time and glad to see it getting down 9 second nitrous passes are right there
Originally Posted by 1961ba427
Awesome results and great conditions at the track too! Congratulations
Originally Posted by GC99TA
Congrats on continuing to improve! I'm getting close to calling Circle D about a new converter for my Camaro. I'm looking for something a little tighter for nitrous passes with the added benefit of being a little more street-driver friendly as well. I was concerned about losing some in the 60' on the motor but your car out 60's mine on the motor with your 9.5inch 4000 stall. Of course I'm probably wasting a lot of energy with all the upward motion. Congrats again!
Thanx guys. I really do enjoy tweaking and measuring. The car is really fun these days. It feel really strong all the time now.
I tried spraying the car the other day and it was blowing through the converter pretty bad. The shift light just stays one when on the juice. I have been reading about guys using 20w hydraulic oil to tighten the converter, so I will probably try that next.
I tried spraying the car the other day and it was blowing through the converter pretty bad. The shift light just stays one when on the juice.
Oh man.....I really didn't want to hear that! I just ordered the same converter today! That wasn't the first time you sprayed the Circle D was it? What were you hitting it with?
Oh man.....I really didn't want to hear that! I just ordered the same converter today! That wasn't the first time you sprayed the Circle D was it? What were you hitting it with?
I sure Chris hasn't built it yet. Did you tell him you were focussed on spray? What trans you have?
I hit mine with an 81n jet tune. It could not take it. I think it makes more power on spray with the new cam.
I sure Chris hasn't built it yet. Did you tell him you were focussed on spray? What trans you have?
I hit mine with an 81n jet tune. It could not take it. I think it makes more power on spray with the new cam.
Chris wasn't around when I calledtoday...I talked to another guy....Brian maybe? But yeah, the conversation was centered around an e-mail chain I had with Chris a while back and I had told him I'm looking to spray 200-250. I don't know that my converter will be exactly like yours (besides being for a TH400) but Chris spec'd a Pro Series Stage III 245mm 3C 4000 stall in his email so that's what the guy sold me today.
Chris wasn't around when I calledtoday...I talked to another guy....Brian maybe? But yeah, the conversation was centered around an e-mail chain I had with Chris a while back and I had told him I'm looking to spray 200-250. I don't know that my converter will be exactly like yours (besides being for a TH400) but Chris spec'd a Pro Series Stage III 245mm 3C 4000 stall.
I would confirm with Chris, but that might be okay. TH400 has higher line pressures feeding the converter which can affect stall. Also, the 3c is a bit tighter than my 4c.