i didn't label where/what i took off very well...so now i'm in process to putting it back...there's bout 10 or so plugs that i'm not exactly sure where it goes...i will in the mean time also...so if anyone knoes wat/where each plug should go plz advise me of so...or lead me to where i can find the info...appreciate anyone's help....

these two are on one group of flex tube...

is this one with the blue rubber for o2?? don't have o2 in my hand so can't vfy...

does this one go into the 6sp tranny??? i have the tranny off so i can't vfy...


these are closer to the red/blue plug to pcm

 

The first one def looks like an O2 sensor and I think that you are right on the trans plug third one not sure fourth I believe is the plug that went into the airbox and fourth look familier but not sure right now

 

there's quite a few of these o2 plugs....anyone know how i can tell which one is which??? i'm trying to avoid from opening up the flex tube and tracing it back...i check the faq and only see the wiring output from the red/blue connector...not the individual plugs themselves...

 

Well, here are some pics of a few of the connectors on the 02 LS1. These are what I could get pretty quickly. I don't have anything like your third picture. I could not get any tranny connectors, the Crank sensor, CAM sensor or either O2. I have everything else....
AC Connector

Driver side Coil

Alternator and Temperature

Air Temp

Knock sensor

MAF, TPS and IAC

Oil Pressure (you don't need this one)

Pass Coil


Hope that helps....

 

This will answer the second to the last one - I also had problems with it : https://ls1tech.com/forums/conversions-swaps/589014-id-connector.html

 

oh shiet...thanx mang...i was gonna post more connectors...but joo covered some of the ones i didn't posted...thanx so much....i got 3 more connector that i'm not sure wat it is...it's all the same type plug...2 is black and 1 is silver but same time connector...2 is grouped together and the 3rd is in the same bundle as another o2 connector by the starter region....

 

In the top picture, the grey on is the MAP, the other is the CAM sensor. In the lower picture, you are holding your Crank Sensor connector, it is behind the starter. I took a picture of the MAP, forgot to post it...

 

oh btw...the harness is from a 2000 camaro 6spd....next time i take the harness of again i'm going to take a pix of the whole thing and label what i knoe each one is so maybe it can help others in the future....

 

thank u again...gonna see where i missed that one at...

 

Good idea. I know that when our car goes in for paint and body, we are pulling the motor and trans for detail work, and plan on completely documenting the harness. It should make repairs/mods much easier in the future...

Oh, does your second pic in the first post have grn/brn wires? If so, that is your backup lamp switch on the pass side of the trans.

 

yeah...it's green and something dark...either brown or black...

and the 3rd pix from first post that no one doesn't seem to knoe wat it is yet ish in a bundle very close to the blue/red connector...here's hopefully a better pix...

 

ok....so i sent to tinker with the harness again...found the map and cam plugs....too dark to find the crank...





these two plugs here appears to be an interior plug...becuz they are on a pigtail and has a rubber gromet in the middle of the pigtail....maybe this may help someone on here identifying this for me...

 

check out this site bro... just scroll down and it has a numbered layout of the wiring harness and what each plug goes to. also has what color every connector's wires are.

ls1 M6- http://www.hotrodlane.cc/Instruction.../InstalT56.pdf

ls1 A4- http://www.hotrodlane.cc/PDFFILES/ls...icharness2.pdf

 

1. 02 SENSOR
2. HARNESS TO CAR UNDERNEATH THE GLOVE BOX
3. TPS CONNECTOR
4. PASSENGER SIDE WHEEL WELL.
Should be another one there also..and a 10g Purple Wire with a Plug.
5. GRAY ON IN THE BACK-MAP SENSOR
BLACK ONE- CRANK POSITION SENSOR

 

i found a similar pdf from s&p while searching....not that one in particular....thanx...also while searching i found out the name of those two plugs are c220 and c230...

 

yeah...that purple i found goes to the starter....so need to splice that to my ignition switch...

 

The White/Blue ones under neather the Dash are names the C-220, and C-230.
The ones on the Wheel Well are named C-100(10 pin black), C-101(10 pin gray), and C-105(8 pin black).

 

Just plug it in to where it goes on the Car..or are you doing something custom.

 

by any chance u knoe or have documentation to the function/pin-layout of these connectors???

 

wat do u mean??? where else would it go in the car other then the ignition switch???? i guess it would be custom since it's a hybrid...