The G-Body Swap Thread
#1023
TECH Enthusiast
iTrader: (5)
I'm suing DBW, But when I had the LT1, I used a Camaro throttle cable. Did any of the early Camaros with LS motors have a cable? I would try that. The body style from LT1 to LS1 in the Camaro didn't change, so I bet it would work. The LT1 cable even had the same clips to mount in the firewall as stock Monte.
#1024
TECH Fanatic
iTrader: (8)
I'm suing DBW, But when I had the LT1, I used a Camaro throttle cable. Did any of the early Camaros with LS motors have a cable? I would try that. The body style from LT1 to LS1 in the Camaro didn't change, so I bet it would work. The LT1 cable even had the same clips to mount in the firewall as stock Monte.
#1026
^^^
Been wondering a little about A/C as well. I know a frame notch is pretty much necessary if you use adapter plates. And BRP I think no notching is needed.
I wonder how a custom bracket would do to push a Sanden compressor out further to line up with rest of the pulley's??
Like this
Or
With the factory truck bracket and compressor maybe even the car compressor & bracket, I think the end of the compressor/bracket hits the mounts with 1in setback plates (for those using that setup)
I would think a custom bracket like above but push it more forward so it's no longer running on its own belt if you use a new Sanden Compressor.
Been wondering a little about A/C as well. I know a frame notch is pretty much necessary if you use adapter plates. And BRP I think no notching is needed.
I wonder how a custom bracket would do to push a Sanden compressor out further to line up with rest of the pulley's??
Like this
Or
With the factory truck bracket and compressor maybe even the car compressor & bracket, I think the end of the compressor/bracket hits the mounts with 1in setback plates (for those using that setup)
I would think a custom bracket like above but push it more forward so it's no longer running on its own belt if you use a new Sanden Compressor.
I did a search of this thread, and maybe I missed it, but certainly need more info. Going to run twin 66's or a big single turbo with A/C and really really don't want to look at the a/c at the top of the engine bay. I got Trans-Dapt 1" set back plates.
my build thread...
https://ls1tech.com/forums/conversio...o-ls-swap.html
#1028
I did a search of this thread, and maybe I missed it, but certainly need more info. Going to run twin 66's or a big single turbo with A/C and really really don't want to look at the a/c at the top of the engine bay. I got Trans-Dapt 1" set back plates.
my build thread...
https://ls1tech.com/forums/conversio...o-ls-swap.html
my build thread...
https://ls1tech.com/forums/conversio...o-ls-swap.html
There is plenty of room for the stock AC compressor
https://ls1tech.com/forums/conversio...m-bracket.html
Just needs a different pulley and custom brackets, or sanden compressor.
Which are those? There are quite a few different mounts on ebay.
#1033
#1035
Anyone using factory floor shifter with 4l60e?
Trying to get the monte floor shifter that was used with 200r4 to work with my 4l60e, using 1in set back plates.
I sold the old 305 and trans a while back, didnt even cross my mind to take the brackets off the original trans if that's all I need for the shifter to work with the 4l60e.
Trying to get the monte floor shifter that was used with 200r4 to work with my 4l60e, using 1in set back plates.
I sold the old 305 and trans a while back, didnt even cross my mind to take the brackets off the original trans if that's all I need for the shifter to work with the 4l60e.
#1036
#1037
Staging Lane
iTrader: (2)
Anyone using stock LS2 corvette accessories in a G-body? The search turned up a few possibilities but no pictures or confirmations. I'd really like to keep my LS2 Maganacharger and use it on my 5.3 swap into my Monte.
Thanks!
EDIT* Found my answer..
https://ls1tech.com/forums/conversio...ssories-2.html
Thanks!
EDIT* Found my answer..
https://ls1tech.com/forums/conversio...ssories-2.html
Last edited by 85mcss; 12-04-2013 at 02:00 PM.
#1038
TECH Enthusiast
iTrader: (5)
Anyone using stock LS2 corvette accessories in a G-body? The search turned up a few possibilities but no pictures or confirmations. I'd really like to keep my LS2 Maganacharger and use it on my 5.3 swap into my Monte.
Thanks!
EDIT* Found my answer..
https://ls1tech.com/forums/conversio...ssories-2.html
Thanks!
EDIT* Found my answer..
https://ls1tech.com/forums/conversio...ssories-2.html
#1040
TECH Enthusiast
iTrader: (5)
Join Date: Aug 2008
Location: Middletown, DE
Posts: 696
Likes: 0
Received 0 Likes
on
0 Posts
Well today I started fitting the f body TSP long tubes to my l92/4l80e.....A lot of cutting needed on the passenger side of trans to fit and I assume the same for the driver side. Also motor mounts and adapter plates need some trimming for the headers to fit. Tomorrow we are hoping to test fit the motor and trans with the headers.
As for the shifter , still trying to find out the best way to hook the 4l80e up and what cables needed. But I will take pictures of the hopeful fitment of the headers.
As for the shifter , still trying to find out the best way to hook the 4l80e up and what cables needed. But I will take pictures of the hopeful fitment of the headers.