Datsun 280z Turbo Build - 5.3 / T7875 / Magnum T56 - Video on page 12!
#123
Joints? These are just universal poly motor mounts from speedway motors. I picked up some 1.5" , 1/8" wall tubing, (1.25" ID).
I had to flatten the tubing some so fit between the bushing because they're narrow.
Mounts
http://www.speedwaymotors.com/Flange...ing,58411.html
also, the tabs are from there too. I just opened the holes up to 1/2"
http://www.speedwaymotors.com/Weld-O...ole,38806.html
I had to flatten the tubing some so fit between the bushing because they're narrow.
Mounts
http://www.speedwaymotors.com/Flange...ing,58411.html
also, the tabs are from there too. I just opened the holes up to 1/2"
http://www.speedwaymotors.com/Weld-O...ole,38806.html
#124
Joints? These are just universal poly motor mounts from speedway motors. I picked up some 1.5" , 1/8" wall tubing, (1.25" ID).
I had to flatten the tubing some so fit between the bushing because they're narrow.
Mounts
http://www.speedwaymotors.com/Flange...ing,58411.html
also, the tabs are from there too. I just opened the holes up to 1/2"
http://www.speedwaymotors.com/Weld-O...ole,38806.html
I had to flatten the tubing some so fit between the bushing because they're narrow.
Mounts
http://www.speedwaymotors.com/Flange...ing,58411.html
also, the tabs are from there too. I just opened the holes up to 1/2"
http://www.speedwaymotors.com/Weld-O...ole,38806.html
That's the awnser I was looking for
#128
A friend of mine was telling me he knew where I could scoop up a decent 280 for the cheap so I started poking around online at the current projects. I have an AL 5.3 sitting around that I have listed in the FS ads. I was thinking if I picked up that chassis my L33 would go in it but if it turns out to be a bust of a chassis I'll still be looking to get rid of it. I also have 799 heads
#129
Finished crossmember.
Finished exhaust
All the fuel system stuff should be here tomorrow, so I'll start assembling that. Working on getting all the brake lines out of the engine bay and tucked away, and then I should be able to finish the inner fenders and engine bay.
Finished exhaust
All the fuel system stuff should be here tomorrow, so I'll start assembling that. Working on getting all the brake lines out of the engine bay and tucked away, and then I should be able to finish the inner fenders and engine bay.
#130
Got this bad boy on last night. Turned out OK if you take into account I was using the edge of my bench top and a hammer to bend it! haha
Didn't weld on as pretty as I'd like - Kinda got in a hurry. It'll clean up and do the job though! Its amazingly more rigid than the pass. side.
Also got the hood bracket attached. Yay hoods.
Didn't weld on as pretty as I'd like - Kinda got in a hurry. It'll clean up and do the job though! Its amazingly more rigid than the pass. side.
Also got the hood bracket attached. Yay hoods.
#131
Finished up my upper intercooler mount / beauty piece That a friend bent up.
Brake line simplification:
Line lock, proportioning valve, and bulkhead fittings to get the lines out of the engine bay.
Another angle. Still a few lines to make, but I'm waiting on my new close radius bender to show up.
Brake line simplification:
Line lock, proportioning valve, and bulkhead fittings to get the lines out of the engine bay.
Another angle. Still a few lines to make, but I'm waiting on my new close radius bender to show up.
#132
Well this seems to be more of a photographic record of what I've done than a forum topic lol, but here's some more progress.
This is a fairly common chassis mod to an S30. Helps to distribute load from strut towers. I'm not a welder or a chassis engineer - I just look at pictures and do my best to replicate.
This is a fairly common chassis mod to an S30. Helps to distribute load from strut towers. I'm not a welder or a chassis engineer - I just look at pictures and do my best to replicate.
#134
#135
I'm thinking that sounds like a good project for some other time. Lol.
I just want to drive this thing, and its sucking my wallet dry!
That would be an easy (ish) mod, but I dont really want to take the time to source parts at the moment......
I just want to drive this thing, and its sucking my wallet dry!
That would be an easy (ish) mod, but I dont really want to take the time to source parts at the moment......
#136
When you get around to it lmk. I can PM you they places i used, simple inexpensive ebay ****.
#137
Looks great! Im gonna have to steal that tran's mount design. Turned out pretty slick!
Not planning on drag racing it? Sure wish I would have done a full cage in mine when it was all apart. I'm too darn lazy to take it all apart again now! Out ran the 10.0 roll-bar requirement the first track visit. Can't imagine yours wouldn't as well.
Not planning on drag racing it? Sure wish I would have done a full cage in mine when it was all apart. I'm too darn lazy to take it all apart again now! Out ran the 10.0 roll-bar requirement the first track visit. Can't imagine yours wouldn't as well.
#139
Looks great! Im gonna have to steal that tran's mount design. Turned out pretty slick!
Not planning on drag racing it? Sure wish I would have done a full cage in mine when it was all apart. I'm too darn lazy to take it all apart again now! Out ran the 10.0 roll-bar requirement the first track visit. Can't imagine yours wouldn't as well.
Not planning on drag racing it? Sure wish I would have done a full cage in mine when it was all apart. I'm too darn lazy to take it all apart again now! Out ran the 10.0 roll-bar requirement the first track visit. Can't imagine yours wouldn't as well.
If all works out, I should have it alive, but not moving. I'll be waiting on the driveshaft to get shortened.
I have 99% of everything to put it together, all I need is time.....
#140
Gotcha... can't imagine it would need to be any more rigid or need more bracing with a full cage...