Speed Engineering Race Version Headers Now Available!!
#402
Just wanted to update you guys on the collector question. We received the set of headers back that were close to the bottom of the car for measuring etc. I bolted a spare block and head together on the table with three sets of our headers. 1 from the old batch, 1 from the new batch, and the current ones returned. All three headers measured within 1/8" of an inch at the tip of the collector. The factories precision on these are crazy accurate, being two foot out with all those bends, and staying within 1/8" of an inch is pretty darn close.
So, the question is why after selling a few hundred headers are we just now seeing a couple customers that have a close fitment issue. We are still looking into differences like larger motor/trany mounts then factory etc.
Either way we are having the factory turn the tip down about 3/8" of an inch to compensate for some of the cars that are closer than usual.
On a side note, we just got word that our 1 7/8" headers are finished up, and heading this way. I would expect to see them within 3 weeks if everything goes smoothly. For those of you interested in the 1 7/8" here is the link again for pre-orders.
http://www.speedengineeringlsx.com/s...ersion-25-1021
Thanks again for your guys business.
Sean
So, the question is why after selling a few hundred headers are we just now seeing a couple customers that have a close fitment issue. We are still looking into differences like larger motor/trany mounts then factory etc.
Either way we are having the factory turn the tip down about 3/8" of an inch to compensate for some of the cars that are closer than usual.
On a side note, we just got word that our 1 7/8" headers are finished up, and heading this way. I would expect to see them within 3 weeks if everything goes smoothly. For those of you interested in the 1 7/8" here is the link again for pre-orders.
http://www.speedengineeringlsx.com/s...ersion-25-1021
Thanks again for your guys business.
Sean
#403
On The Tree
Join Date: Jul 2013
Location: Weymouth, MA
Posts: 174
Likes: 0
Received 0 Likes
on
0 Posts
#404
Staging Lane
iTrader: (2)
Join Date: Jan 2013
Location: So Cal
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
I am interested in pre ordering the 1 7/8" headers and a y pipe but have a couple questions. you have the TSP catted y listed and on your site it states it fits tsp, pacesetter and hooker headers, but not your own. do they not mate well? and also is the TSP y you guys carry the new stainless steel one?
#406
TECH Junkie
iTrader: (11)
Just wanted to update you guys on the collector question. We received the set of headers back that were close to the bottom of the car for measuring etc. I bolted a spare block and head together on the table with three sets of our headers. 1 from the old batch, 1 from the new batch, and the current ones returned. All three headers measured within 1/8" of an inch at the tip of the collector. The factories precision on these are crazy accurate, being two foot out with all those bends, and staying within 1/8" of an inch is pretty darn close.
So, the question is why after selling a few hundred headers are we just now seeing a couple customers that have a close fitment issue. We are still looking into differences like larger motor/trany mounts then factory etc.
Either way we are having the factory turn the tip down about 3/8" of an inch to compensate for some of the cars that are closer than usual.
On a side note, we just got word that our 1 7/8" headers are finished up, and heading this way. I would expect to see them within 3 weeks if everything goes smoothly. For those of you interested in the 1 7/8" here is the link again for pre-orders.
http://www.speedengineeringlsx.com/s...ersion-25-1021
Thanks again for your guys business.
Sean
So, the question is why after selling a few hundred headers are we just now seeing a couple customers that have a close fitment issue. We are still looking into differences like larger motor/trany mounts then factory etc.
Either way we are having the factory turn the tip down about 3/8" of an inch to compensate for some of the cars that are closer than usual.
On a side note, we just got word that our 1 7/8" headers are finished up, and heading this way. I would expect to see them within 3 weeks if everything goes smoothly. For those of you interested in the 1 7/8" here is the link again for pre-orders.
http://www.speedengineeringlsx.com/s...ersion-25-1021
Thanks again for your guys business.
Sean
I usually pie cut the collector and re weld it to make it straight when I put them on.
Bottom line.....its still a good deal when you can get polished stainless steel headers for this price.
By the way....here is a pic of this same design that has had the upgrades like high velocity merge, collector spike, and the angle of the collector fixed.
Last edited by Full-Force; 06-04-2014 at 08:58 AM.
#407
They have always had the angle issue. Why people are just now mentioning it I dont know. The angle on the driver side has always been like that on this header which is the same design sold under various names. You dont need to bolt them up to see it. You can look at the flange and the collector and clearly see the major upward angle of the collector. The only company to take this design and make the driver side collector straight is LPP which I dont think carries this header anymore. They had the collector straightened out and had a high velocity merge collector added. A shame they dont have them anymore. Maybe you guys should try to find who was making theirs for them.
I usually pie cut the collector and re weld it to make it straight when I put them on.
Bottom line.....its still a good deal when you can get polished stainless steel headers for this price.
By the way....here is a pic of this same design that has had the upgrades like high velocity merge, collector spike, and the angle of the collector fixed.
I usually pie cut the collector and re weld it to make it straight when I put them on.
Bottom line.....its still a good deal when you can get polished stainless steel headers for this price.
By the way....here is a pic of this same design that has had the upgrades like high velocity merge, collector spike, and the angle of the collector fixed.
Our race 1 3/4" & 1 7/8" headers are our proprietary design we had built just for us. We launched our headers back in December. This is the style of our race version:
Thanks
Sean
#412
TECH Junkie
iTrader: (11)
I am not really sure what your talking about. Those are not like our race version longtube headers. And we are the only ones selling our design. I think you might be confused with the air/egr version we offer. Which was stated a long time ago that those are just a generic header we get out of China with a 1 5/8" primary. I know there are several people that sell that style.
Our race 1 3/4" & 1 7/8" headers are our proprietary design we had built just for us. We launched our headers back in December. This is the style of our race version:
Thanks
Sean
Our race 1 3/4" & 1 7/8" headers are our proprietary design we had built just for us. We launched our headers back in December. This is the style of our race version:
Thanks
Sean
Its amazing how some things get cheaper and cheaper while others get higher and higher. These are such a smart investment
#414
I am not sure if ours and TSP Y-Pipes are the same. We both get them out of China. They look the similar, so it wouldn't surprise me. We are actually in the middle of making a few changes to our Y-Pipe actually. Were having them add an O2 Bung for wideband tuning, added slots on the female ends to help with better clamping, and are changing one of the clamps out to a smaller dia for the rear connection. It will probably be 5-6 months before we have them on hand however. The basic design will still be fairly similar though.
nocooler: Thank you for your order. Much appreciated.
AnotherWs6: No kidding. lol, I think we have about 7 pre-orders currently.
Thanks again guys..
Sean
nocooler: Thank you for your order. Much appreciated.
AnotherWs6: No kidding. lol, I think we have about 7 pre-orders currently.
Thanks again guys..
Sean
#415
It's not mine! woo hoo!
iTrader: (7)
Do yourself a favor and just get the Speed Engineering y-pipe if you're going with SE headers
And I know I've mentioned this before, but the F-Body LS community owes you a debt of gratitude for the time and effort you're spending on this very old platform. Further, that you continue to be completely candid answering out questions speaks volumes of your integrity.
One last thing... as for the whole collector "issue" -- I've helped install two sets of the current batch and there were no fitment issues whatsoever. Both were with y-pipes.
#419
TECH Addict
iTrader: (17)
And I know I've mentioned this before, but the F-Body LS community owes you a debt of gratitude for the time and effort you're spending on this very old platform. Further, that you continue to be completely candid answering out questions speaks volumes of your integrity.
#420
On The Tree
Join Date: Jul 2013
Location: Weymouth, MA
Posts: 174
Likes: 0
Received 0 Likes
on
0 Posts
http://www.speedengineeringlsx.com/s...ersion-25-1021