Speed Engineering Race Version Headers Now Available!!
Nice talking with you T2TA. Just a heads up concerning the clamps. We have finally received a decent set of clamps. After 3 years of complaining to the factory. They now fit properly with the wedge, and have much better clamping power. I think you guys will be much happier with our most recent batch of clamps.
Thanks
Sean
Thanks
Sean
If I already have a set of your headers and am just going to order a y pipe by itself this time around, does the y pipe alone come with any clamps included? I would have just ordered it all at once from the beginning but my original plan was to run TDs so I didnt need the y pipe when i ordered the headers.
I am extremely happy with mine
Teching In
Joined: Aug 2016
Posts: 19
Likes: 0
From: VA
Thanks Sean. Just submitted order! Looking forward to getting them on.
Now just debating whether to delve into replacing motor mounts. 17k miles. Weekend car. But. I have feeling I may regret not doing when I'm installing the headers. Lol
Thanks again!
Now just debating whether to delve into replacing motor mounts. 17k miles. Weekend car. But. I have feeling I may regret not doing when I'm installing the headers. Lol
Thanks again!
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Teching In
Joined: Aug 2016
Posts: 19
Likes: 0
From: VA
Just received the shipment .. all looks awesome.
Going to be chasing the Drag Week guys around this week and biz trip next week ... then they'll go on with cat back all at once (Magnaflow) hopefully by end of month!
Thanks for all help Sean!
Going to be chasing the Drag Week guys around this week and biz trip next week ... then they'll go on with cat back all at once (Magnaflow) hopefully by end of month!
Thanks for all help Sean!
Teching In
Joined: Aug 2016
Posts: 19
Likes: 0
From: VA
Which is the better gasket to use? Thanks again all!
Top one has dots and seems like material blend of metal and fabric.
Bottom one is all metal (and appears to have two layers each).
Thanks!!
All steel one - bottom gasket better.
Top one has dots and seems like material blend of metal and fabric.
Bottom one is all metal (and appears to have two layers each).
Thanks!!
All steel one - bottom gasket better.
Last edited by T2TA; Sep 10, 2016 at 10:10 PM. Reason: Found answer about 10 pages back.
I got both when I bought mine. I had to research which ones were the better ones. Hands down, the metal 2-layer ones are the ones to use. Good luck with your install.
I have had my 1 3/4 on for over 2 years now, still going good. I have the first gen y-pipe that I had to slot myself so it would clamp better but have yet to have any issues at all with mine. I do recommend doing motor mounts while you are in that deep just to be on the safe side.
You guys keep making a good header even better.
Packaging was excellent, welds are top notch all around.
Nice bends nice finish. Port matched primaries.
Cant beat this deal.