400+ cam only cars!!!
#1
400+ cam only cars!!!
i have a 99 formula M6 car..right now she is getting forged goodies and she has every upgrade i can get right now w/ the acception of under drive pulley, and expensive intake set up...everything else is done...
i am currently running a lunati 234/236 .050 .544/.545 112 lsa cam...i made 380 rwhp and 350 tq when tuned and dynod...i am looking for the 415+ hp and more torque from a cam only set up...and since everybody is going to ask about my mods...i will list ahead of time...
slp lid, SLP cool air pak, K&N filter(s), smooth bellow, 80 mm BBK TB, LS6 intake, MSD wires, NGK Plugs, 853 heads( 3 angle valve job, new locks, guides, retainers) comp hardened pushrods, crane springs .650 lift,crane lifters, ported LS6 oil pump,dbl roller timing chain,polished crank, mahle forged pistons, eagle forged H beam rods, SLP Lt's, 3" ORY loudmouth w/ tips, no cats, no converters...i think that's it...and since suspention stuff doesnt really count on this..i will leave it out..
anyways like i said i am looking for that 415-430 hp cam only #'s
i am currently running a lunati 234/236 .050 .544/.545 112 lsa cam...i made 380 rwhp and 350 tq when tuned and dynod...i am looking for the 415+ hp and more torque from a cam only set up...and since everybody is going to ask about my mods...i will list ahead of time...
slp lid, SLP cool air pak, K&N filter(s), smooth bellow, 80 mm BBK TB, LS6 intake, MSD wires, NGK Plugs, 853 heads( 3 angle valve job, new locks, guides, retainers) comp hardened pushrods, crane springs .650 lift,crane lifters, ported LS6 oil pump,dbl roller timing chain,polished crank, mahle forged pistons, eagle forged H beam rods, SLP Lt's, 3" ORY loudmouth w/ tips, no cats, no converters...i think that's it...and since suspention stuff doesnt really count on this..i will leave it out..
anyways like i said i am looking for that 415-430 hp cam only #'s
#2
Banned
iTrader: (19)
Join Date: Jun 2005
Location: chitown
Posts: 1,879
Likes: 0
Received 0 Likes
on
0 Posts
are you looking for e.t. improvements, or just a dyno number? i would recommend going with a FAST intake to make the most of a cam only combination. that way you might not have to go with such a ginormous cam to hit the number.
we have hit 410rwhp recently with our SI6 cam and ls6 intake (cam-only) for what it's worth.
we have hit 410rwhp recently with our SI6 cam and ls6 intake (cam-only) for what it's worth.
#5
On The Tree
iTrader: (4)
Join Date: Jan 2006
Location: TX
Posts: 183
Likes: 0
Received 0 Likes
on
0 Posts
Link to cam-only thread, not all at your goal but that gives you an idea of the cam size, also if you are gettin forged pistons, get some with valve relief and have your heads milled for bump in comp., A trex or a ms4 should do it for you.
https://ls1tech.com/forums/dynamometer-results-comparisons/219024-cam-only-dyno-thread.html
https://ls1tech.com/forums/dynamometer-results-comparisons/219024-cam-only-dyno-thread.html
Trending Topics
#9
Banned
iTrader: (1)
those lobes on that lunati cam are pretty lazy and the lift is kinda low. Those lobes are probably more like a 224/228 after .200 lift and don't even carry lift as high.
lots of the high end cams will get you to your HP goal, but the size of the lobes needed will open the exhaust valve too soon to get amazing tq numbers. To get those you're going to need to pull the heads, mill for compression and flycut, or you'll need better heads all together.
lots of the high end cams will get you to your HP goal, but the size of the lobes needed will open the exhaust valve too soon to get amazing tq numbers. To get those you're going to need to pull the heads, mill for compression and flycut, or you'll need better heads all together.
#11
On The Tree
iTrader: (4)
Join Date: Aug 2007
Location: Delaware
Posts: 183
Likes: 0
Received 0 Likes
on
0 Posts
I made 391/386 on a Mustang dyno Cam only in a stalled A4. Mods are 3:73's, CAI, full exhaust w/ ORY, Built tranny w/ Vig.3200 stall, and a RPM2 cam
(232/234 595/598 on a 112) I should be around 410+/- on a dynojet.
(232/234 595/598 on a 112) I should be around 410+/- on a dynojet.
#13
I think your HP# is doable cam only but to have 4+ hp/tq cam only is going to be tough.
I agree with milling to bump comp. and hope for more tq but 4+ I don't know. I put 404rwhp and 374rwtq with cats on after market rims that are a little heavy. The car could have done maybe 410+ with no cats and stock rims but the TQ I'm sure would have never gone past 380-385. My cam is the TSP Torquer 3
I agree with milling to bump comp. and hope for more tq but 4+ I don't know. I put 404rwhp and 374rwtq with cats on after market rims that are a little heavy. The car could have done maybe 410+ with no cats and stock rims but the TQ I'm sure would have never gone past 380-385. My cam is the TSP Torquer 3
#15
12 Second Club
Join Date: Mar 2005
Location: Corpus Christi
Posts: 1,498
Likes: 0
Received 0 Likes
on
0 Posts
well! 2001 WS6 M6, Comp Cam 231/237 .589/.595 112+4 lsa 112, cnc LS6 Patriot Perf 59cc 2.02in/1.87 ex, kooks Lt, x-pipe, bullets dumped no cats, ported TB, stock intake (ls6), Granatellis' maf sensor, SLP lid, K&N filter. 418rwhp/389rwtq..... mustang dyno.............
#16
10 Second Club
iTrader: (2)
Join Date: Aug 2005
Location: Ottawa, IL
Posts: 956
Likes: 0
Received 0 Likes
on
0 Posts
I just put down 402 rwhp and 374 rwtq in my 2000 M6 SS with Speed Inc. SI5 cam using a Fast/NW intake setup. These numbers are also through a heavy drivetrain that includes an LS7 clutch and a 9"w/3.89 gears. The rest of my mods are in my sig.
#17
TECH Fanatic
iTrader: (4)
Join Date: Jul 2003
Location: Orange Park/ Jacksonville, FL
Posts: 1,075
Likes: 0
Received 0 Likes
on
0 Posts
I put down 393hp/383tq on the old tune w/ an ASA cam (226/236 .525 110lsa).
No #'s w/ the new tune, but I picked up 3 tenths and 4mph @ the track, so I'm assuming I'm in the neighborhood of 400hp now.
No #'s w/ the new tune, but I picked up 3 tenths and 4mph @ the track, so I'm assuming I'm in the neighborhood of 400hp now.
#19
12 Second Club
iTrader: (6)
Join Date: Oct 2007
Location: Shawnee (Shawmpton), OKlahoma
Posts: 126
Likes: 0
Received 0 Likes
on
0 Posts
I am running an MS4 in my M6 car. I have a ported TB, underdrives, FTRA, and MSD wires. I made 434 RWHP on a Dynojet dyno, With a 9in witch eats some power. I say go with an MS4, I have had no problems with it driveable wise and it sounds mean as hell!