LSX 454 freshen up
#181
TECH Enthusiast
Thread Starter
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Priority mains.. Oil pressure is pegged. standard volume high pressure. Im thinking of dropping the new low volume pump in.
Ill see where power starts to drop and set limiter 300rpm higher
Ill see where power starts to drop and set limiter 300rpm higher
#182
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I would definitely say you need it at 8000rpm.
#183
Moderator
iTrader: (4)
Join Date: Jul 2014
Location: My own internal universe
Posts: 10,446
Received 1,838 Likes
on
1,146 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by Mickyinks
Priority mains.. Oil pressure is pegged. standard volume high pressure. Im thinking of dropping the new low volume pump in.
Ill see where power starts to drop and set limiter 300rpm higher
Ill see where power starts to drop and set limiter 300rpm higher
#184
TECH Enthusiast
Thread Starter
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Maybe im being a bit cautious then. 1st solid roller v8 ive had, used to the hyd going 6800rpm.
Im not going to rev it for the sake of it and it spins up easy as it is.
I just took my daughters friend for a squirt and had wheel spin 1st ,2nd,3rd and into 4th with 7000rpm shifts
Im not going to rev it for the sake of it and it spins up easy as it is.
I just took my daughters friend for a squirt and had wheel spin 1st ,2nd,3rd and into 4th with 7000rpm shifts
Last edited by Mickyinks; 01-25-2020 at 07:34 AM.
The following users liked this post:
Che70velle (01-25-2020)
#186
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Maybe im being a bit cautious then. 1st solid roller v8 ive had, used to the hyd going 6800rpm.
Im not going to rev it for the sake of it and it spins up easy as it is.
I just took my daughters friend for a squirt and had wheel spin 1st ,2nd,3rd and into 4th with 7000rpm shifts
Im not going to rev it for the sake of it and it spins up easy as it is.
I just took my daughters friend for a squirt and had wheel spin 1st ,2nd,3rd and into 4th with 7000rpm shifts
I forget is your car manual?
#189
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Back in the early days of LS's a lot of us were too afraid to rpm even just cammed or head/cammed sbe cars too high because the cars and engines were new to us and expensive to replace back then. Now we realize we can spin junkyard stuff to 8k because the engine didn't cost much so we tested the waters.
If you're not drag racing or trying to achieve the best 1/4 mile ET, and have more HP than you need or your car can put to the ground, then it's not worth spinning so high past peak power unless just for the fun factor. Not worth it for the OP's build, as I imagine his mid range power/torque alone would overtake most cars on the road like they're parked still.
#190
Moderator
iTrader: (4)
Join Date: Jul 2014
Location: My own internal universe
Posts: 10,446
Received 1,838 Likes
on
1,146 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by Mickyinks
Maybe im being a bit cautious then. 1st solid roller v8 ive had, used to the hyd going 6800rpm.
Im not going to rev it for the sake of it and it spins up easy as it is.
I just took my daughters friend for a squirt and had wheel spin 1st ,2nd,3rd and into 4th with 7000rpm shifts
Im not going to rev it for the sake of it and it spins up easy as it is.
I just took my daughters friend for a squirt and had wheel spin 1st ,2nd,3rd and into 4th with 7000rpm shifts
The following users liked this post:
Che70velle (01-25-2020)
#192
9 Second Club
iTrader: (18)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by Launch
Even on my current heap of sh*t cam-only 346 I found it will et quicker on my gtech every time when I shift at 7400-7500 rpm than if I shift at a lower rpm. And the cam isn't even that large. Limiter set to 8k so I never hit it by mistake but I have hit 8k a few times. I've spent almost nothing on that engine so I don't care.
Back in the early days of LS's a lot of us were too afraid to rpm even just cammed or head/cammed sbe cars too high because the cars and engines were new to us and expensive to replace back then. Now we realize we can spin junkyard stuff to 8k because the engine didn't cost much so we tested the waters.
If you're not drag racing or trying to achieve the best 1/4 mile ET, and have more HP than you need or your car can put to the ground, then it's not worth spinning so high past peak power unless just for the fun factor. Not worth it for the OP's build, as I imagine his mid range power/torque alone would overtake most cars on the road like they're parked still.
Back in the early days of LS's a lot of us were too afraid to rpm even just cammed or head/cammed sbe cars too high because the cars and engines were new to us and expensive to replace back then. Now we realize we can spin junkyard stuff to 8k because the engine didn't cost much so we tested the waters.
If you're not drag racing or trying to achieve the best 1/4 mile ET, and have more HP than you need or your car can put to the ground, then it's not worth spinning so high past peak power unless just for the fun factor. Not worth it for the OP's build, as I imagine his mid range power/torque alone would overtake most cars on the road like they're parked still.
Originally Posted by Darth_V8r
My comment was really for racing. Power past peak is an often untapped gold mine at the track. Street driving, 8k gets you noticed from a mile away
#193
TECH Enthusiast
Thread Starter
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Ok Limiter is set at 8000rpm
Was pulled over by the cops yesterday. To low and said my new tyres arn't legal. Argued with him but he wouldnt budge. So now need raise height and new tyres for road worthy certificate
Driving home was just bout home and sprung a leak from oil cooler somewhere, oil temps fine , pressure fine, just a line of oil about a kilometre long... Other than that 300miles and didnt miss a beat...
Anytime Bortous
Was pulled over by the cops yesterday. To low and said my new tyres arn't legal. Argued with him but he wouldnt budge. So now need raise height and new tyres for road worthy certificate
Driving home was just bout home and sprung a leak from oil cooler somewhere, oil temps fine , pressure fine, just a line of oil about a kilometre long... Other than that 300miles and didnt miss a beat...
Anytime Bortous
#194
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Ok Limiter is set at 8000rpm
Was pulled over by the cops yesterday. To low and said my new tyres arn't legal. Argued with him but he wouldnt budge. So now need raise height and new tyres for road worthy certificate
Driving home was just bout home and sprung a leak from oil cooler somewhere, oil temps fine , pressure fine, just a line of oil about a kilometre long... Other than that 300miles and didnt miss a beat...
Anytime Bortous
Was pulled over by the cops yesterday. To low and said my new tyres arn't legal. Argued with him but he wouldnt budge. So now need raise height and new tyres for road worthy certificate
Driving home was just bout home and sprung a leak from oil cooler somewhere, oil temps fine , pressure fine, just a line of oil about a kilometre long... Other than that 300miles and didnt miss a beat...
Anytime Bortous
What was illegal about your tyres?
That oil leak would **** me off.
#195
TECH Enthusiast
Thread Starter
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Nothing is illegal about them michelin sport cup 2 semi slick... Still plenty on the depth gauge... Wouldnt listen at all, pulled receipt out they only 7 weeks old
Need new oil coller ,sprung a leak
#196
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
They asked me to start the car and they listened to the exhaust. Said it was all good... I Love my Varex hahaha
Nothing is illegal about them michelin sport cup 2 semi slick... Still plenty on the depth gauge... Wouldnt listen at all, pulled receipt out they only 7 weeks old
Need new oil coller ,sprung a leak
Nothing is illegal about them michelin sport cup 2 semi slick... Still plenty on the depth gauge... Wouldnt listen at all, pulled receipt out they only 7 weeks old
Need new oil coller ,sprung a leak
That's awesome.
They are pretty strict with the ride height though.
When my vz was checked years ago it was just on legal.
I wonder if they checked the load rating of the tyre too.
Was the oil cooler faulty?
#197
TECH Enthusiast
Thread Starter
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I have 3inch cat back hollowed out cats varex mufflers... When they asked me to start it i pushed the button and the varex mufflers went into super quiet mode.. If i have em open its super load .
No load rating check, said not enough tread, ..Told him they semi slicks and thats how they are, check depth indicator. Wouldnt listen
oil cooler cracked ...
No load rating check, said not enough tread, ..Told him they semi slicks and thats how they are, check depth indicator. Wouldnt listen
oil cooler cracked ...
#198
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I have been looking at fitting those mufflers too.
There will come a day when I will get checked.
Do you know if those varax mufflers are also compatible with the vt-vz chassis?
There will come a day when I will get checked.
Do you know if those varax mufflers are also compatible with the vt-vz chassis?
The following users liked this post:
G Atsma (01-27-2020)
#200
TECH Enthusiast
Thread Starter
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
A set of new rear tyres, raised the car by an inch, new B&M engine oil cooler, a road worthy certificate and im back on the road.......