Fireball Outlaw Drag Radial Rebuild Thread
#1503
TECH Senior Member
Thread Starter
iTrader: (21)
Join Date: Nov 2001
Location: Cecil County Raceway!!!
Posts: 8,484
Likes: 0
Received 0 Likes
on
0 Posts
scavenge pump is fixed. I put in some allen head screws with some loctite to secure the pump to the bracket. Also put a large hose clamp around the pump and bracket to further secure it....
have a higher pressure sensor for my AMS1000 on the way so I can get the boost higher than the low 30s
plan on making some more hits tomorrow night
have a higher pressure sensor for my AMS1000 on the way so I can get the boost higher than the low 30s
plan on making some more hits tomorrow night
#1504
TECH Senior Member
Thread Starter
iTrader: (21)
Join Date: Nov 2001
Location: Cecil County Raceway!!!
Posts: 8,484
Likes: 0
Received 0 Likes
on
0 Posts
0 for 3 last night
first pass...1.39 60', blew the tires HARD at 100' out....car went completely sideways at 75mph
2nd pass...1.36 60'... had a sync loss with my crank sensor at top of first gear (aborted)...tightened up the gap some more...
3rd pass...1.33 60'...idiots at the track wasn't paying attention and let a truck roll down next to me after I started building boost. Had to back off and restart...most likely overheated the converter/trans and blew through 2nd gear bad
fugger is making some serious power now...hit 33psi...Ended up going 9.80 only in the gas for 300ft
first pass...1.39 60', blew the tires HARD at 100' out....car went completely sideways at 75mph
2nd pass...1.36 60'... had a sync loss with my crank sensor at top of first gear (aborted)...tightened up the gap some more...
3rd pass...1.33 60'...idiots at the track wasn't paying attention and let a truck roll down next to me after I started building boost. Had to back off and restart...most likely overheated the converter/trans and blew through 2nd gear bad
fugger is making some serious power now...hit 33psi...Ended up going 9.80 only in the gas for 300ft
#1507
TECH Senior Member
Thread Starter
iTrader: (21)
Join Date: Nov 2001
Location: Cecil County Raceway!!!
Posts: 8,484
Likes: 0
Received 0 Likes
on
0 Posts
first run (definately drove out of the groove...probably why it spun)
http://www.youtube.com/watch?v=M21M0TGNRfE
third run (blew through the shift and hit the rev limiter...pretty cool fireballs In the gas ~4seconds... and coasted to a 9.80
http://www.youtube.com/watch?v=mVIMfGSU_wo
http://www.youtube.com/watch?v=M21M0TGNRfE
third run (blew through the shift and hit the rev limiter...pretty cool fireballs In the gas ~4seconds... and coasted to a 9.80
http://www.youtube.com/watch?v=mVIMfGSU_wo
#1511
TECH Senior Member
Thread Starter
iTrader: (21)
Join Date: Nov 2001
Location: Cecil County Raceway!!!
Posts: 8,484
Likes: 0
Received 0 Likes
on
0 Posts
trans is freshened up and back in the car...
parts are coming today so I can weld a transcooler into my icewater tank. Extra cooling should help out
gonna try to make a few hits tomorrow if all pans out...
parts are coming today so I can weld a transcooler into my icewater tank. Extra cooling should help out
gonna try to make a few hits tomorrow if all pans out...
#1519
TECH Senior Member
Thread Starter
iTrader: (21)
Join Date: Nov 2001
Location: Cecil County Raceway!!!
Posts: 8,484
Likes: 0
Received 0 Likes
on
0 Posts
I was never a sponsor...
One of my sponsors was a sponsor, but temporarily closed up shop while he was building a new house.
I did alot of watching and learning while hanging out there...this whole rebuild was done in my 2-car garage
Only things I didn't do was the engine or trans builds