Speed Engineering Race Version Headers Now Available!!
03-03-2014, 10:45 AM
#162
From what I gathered is that the fit is good on headers and y pipe but the clamps are not the best.
Speed Engineering do yall plan to change the clamps or offer another type of band? I just hate to spend more money on other clamps.
I think I am going to buy SE headers and tsp y pipe. Open to opinions on this as well.
Speed Engineering do yall plan to change the clamps or offer another type of band? I just hate to spend more money on other clamps.
I think I am going to buy SE headers and tsp y pipe. Open to opinions on this as well.
LFSADRG: No, I believe we also mentioned it earlier. The Air/EGR version is more of a generic version we get out of China. Its not proprietary to us, and we don't plan on creating a new Air/EGR version.
Thanks
Sean
03-03-2014, 11:46 AM
#163
From what I gathered is that the fit is good on headers and y pipe but the clamps are not the best.
Speed Engineering do yall plan to change the clamps or offer another type of band? I just hate to spend more money on other clamps.
I think I am going to buy SE headers and tsp y pipe. Open to opinions on this as well.
Speed Engineering do yall plan to change the clamps or offer another type of band? I just hate to spend more money on other clamps.
I think I am going to buy SE headers and tsp y pipe. Open to opinions on this as well.
The only clamp concern that one may have is the clamp for the intermediate pipe. As I mentioned previously, it's 2.75", so one needs to salvage the factory clamp (which has a small tack weld) or you'll need to have a smaller clamp ready for the install as the kits (again, this is also a TSP issue) only come with 3" clamps.
03-04-2014, 01:01 PM
#164
Teching In
iTrader: (1)
Join Date: Jan 2014
Location: Dallas,Texas
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
As mentioned in my write-up, TSP uses identical clamps for their systems as well. The easiest/cheapest way to handle it is notch the female pipe as Sean mentioned. The clamps they send aren't junky clamps; however, the pipes are slighter larger ID for what I assume to be ease of install. Again, this is the same situation one will encounter with TSP.
03-07-2014, 06:09 PM
#172
TECH Enthusiast
In the future, hopefully NEAR future, will there be 1 7/8" and 2" diameter primaries available ?
Would they be available on both race and non-race headers ?
Thanks !
Would they be available on both race and non-race headers ?
Thanks !
03-08-2014, 07:42 AM
#173
TECH Fanatic
iTrader: (12)
Join Date: Apr 2007
Location: Douglasville, GA
Posts: 1,276
Likes: 0
Received 0 Likes
on
0 Posts
Anyone that could get me a measurement on how low they drop down?
I am trying to see if they will be below the frame or not on my c10.
A measurement from the flange down to the top or bottom of the collector would be awesome!
Thanks
I am trying to see if they will be below the frame or not on my c10.
A measurement from the flange down to the top or bottom of the collector would be awesome!
Thanks
03-13-2014, 07:44 AM
#176
On The Tree
iTrader: (2)
Join Date: Oct 2011
Location: Abilene, TX
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
I purchased a set of headers on ebay about 3 years ago but ebay wont let me go that far back to see history. Even so I wanna say these were purchased from speed engineering back then but not entirely sure. If so, I would have to agree fitment is amazing and so is quality for budget stainless headers. Really enjoying mine since install.
